Bruksanvisning Electrolux EFP663 Köksfläkt

Bruksanvisning

Particular care must be paid to the grease grille

which must be periodically cleaned in relation to

use (at least once every two months). Remove

the grease grille and wash them either by hand

or in the dishwasher using neutral detergent.

Any fat deposits should be removed from the

appliance periodically depending on amount of

use (at least every 2 months). Avoid using abra-

sive or corrosive products. To clean painted

appliances on the outside, use a cloth dipped in

lukewarm water and neutral detergent. To clean

steel, copper or brass appliances on the outside,

it is always best to use specific products, following

the instructions on the products themselves. To

clean the inside of the appliance, use a cloth (or

brush) dipped in denatured ethyl alcohol.

DESCRIPTION

-----------------------------------------------------------

The appliance can be used in both the filtering and

ducting version.

In the Filtering version (Fig. 1), the air and va-

pours conveyed by the appliance are depurated

by charcoal filter(s) and recirculated around the

room. ATTENTION: Using the hood as a filtering

one it is necessary to use the charcoal filter(s) that

purifies the air sent back into the room.

In the Ducting version (Fig. 2), cooking vapours

and odours are conveyed straight outside by a

disposal duct which passes through the wall/ceil-

ing. Use of charcoal filter is therefore unneces-

sary.

According to the model you have bought, the ap-

pliance can include 1 or 2 motors. In the I motor

version the flange for the air to be exhausted has

not got a central position, but it is slightly on the left.

INSTALLATION

-----------------------------------------------------------

Before assembling, in order to manoeuvre the

appliance more easily, take off the grease grille

(Fig. 3): pull the front of the grille upwards; desinsert

the back from its seat.

IMPORTANT: So as not to damage your

product, during installation USE ONLY THE

SCREWS PROVIDED. Make sure these are used

as shown in the following instructions.

To compensate possible depth voids between

the appliance and the wall, a plastic SPACING

BAR to be fixed at the back of the appliance by

means of the three screws A is included (Fig.4).

The 3 screws A to be used are contained in the

accessory bag attached to the plastic spacing

bar. Cut the spacing bar according to the

distance to be adjusted.

Assembly under a pensile cupboard

The following operations are essential for as-

sembly:

– Install the wiring system

– Prepare the air venting hole if your appliance

is to be installed in the Ducting version.

Fixation as indicated in Fig. 5:

Using the relative template make the 4 neces-

sary fixing holes in the bottom of the cup-

board and cut the air venting hole.

Move the hood close to the bottom of the wall

unit and then connect the two units by means

of the 4 self-tapping screws supplied together

with the appliance.

Fixation with brackets as in Fig. 6 (optional):

Take the two brackets (S) out of the accessory

bag together with the 8 screws provided. Fit

the brackets to the wall unit being careful to

position these correctly; for this operation

use the 4 longer screws. At this point, secure

the appliance to the brackets using the 4

shorter screws.

Ducting version: connect the flange of the hood

with the air venting hole made previously in the wall/

ceiling by means of an adequate tube. Make the

electrical connection of the hood by means of the

power supply cable. Assemble the grease grille

with the hood, inserting it obliquely (making the

front side go upwards).

Filtering version: connect a proper pipe to the

flange of the hood so that the air is sent outside the

pensile and sent back into the room. Make the

electrical connection of the hood by means of the

power supply cable. Set the charcoal filter inside

the grease grille blocking it by means of the 2

supplied metal wires (F), as indicated in Fig. 3.

Assemble the grease grille with the hood, inserting

it obliquely (making the front side go upwards).

OPERATION

-----------------------------------------------------------

Controls (Fig. 7):

A = ON/OFF 1st speed switch

B = II speed switch

C = III speed switch

The motor is automatically ON or OFF by

opening/closing the truck (unless switch A is

on 0). Opening the truck the motor works

according to last speed registered.

D = Light switch:position A (automatic), the light

are automatically regulated ON or OFF by

the opening/closing of the truck. Position M

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Electrolux EFP663 Köksfläkt. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Electrolux. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Electrolux EFP663 Köksfläkt på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Electrolux Köksfläktar
Fler bruksanvisningar för Köksfläktar

Vanliga frågor om Electrolux EFP663 Köksfläkt

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Electrolux LFV446K Köksfläkt

Bruksanvisning

Electrolux LFV619Z Köksfläkt

Bruksanvisning

Electrolux EFT6220X Köksfläkt

Bruksanvisning

Electrolux LFC516X Köksfläkt

Bruksanvisning

Electrolux YFP616X Köksfläkt

Bruksanvisning

Electrolux LFV636K Köksfläkt

Bruksanvisning

Electrolux LFV329W Köksfläkt

Bruksanvisning

Electrolux EFV729Z Köksfläkt

Relaterade kategorier