Bruksanvisning Chef'sChoice Asian 316 Knivslip

Bruksanvisning

6

SharpenIng the tradItIonal (SIngle bevel)

JapaneSe blade

Traditional Japanese knives are single sided and have a large factory bevel (Bevel A, page 9) on

one side of the blade. There are a large number of manufacturers of knives of this type which

are used widely to prepare sashimi. The factory bevel (Bevel A) is commonly ground at about 10

degrees, but there are exceptions and that angle is not standardized at the factories. Designs of

the traditional Japanese knives and the detailed structure of the cutting edges likewise varies

widely from one manufacturer to the next, however there are some similarities. The cutting edge

consists of a small primary facet on the front face of the blade and a much smaller secondary

microfacet along the back face. Commonly the back side microfacet (Figure 10) can be easily

seen only with a hand magnifier. The back face is ground flat at the factory or more commonly

it is slightly hollow ground to ensure that an effective microfacet can be formed there as part of

the cutting edge. Because of the lack of standardization, commonly the manual approach used

to sharpen these knives has proven difficult, laborious and time consuming. The Chef’sChoice

®

Model 316 Sharpener is designed to sharpen all but the heaviest contemporary and traditional

Asian blades and to create a factory-like edge.

Before you start to sharpen a traditional blade, examine it carefully in order to confirm that

you have the traditional single bevel blade and to determine whether you have a right or left

handed type as described on page 9. It is important that you follow carefully the sharpening

procedure and sequence as described below in order to achieve the optimum edge on your

traditional blade.

Note: Do not attempt to sharpen any traditional blade thicker than 1/8 inch (3 mm) in the Model

316 sharpener. (Control of the sharpening angle becomes difficult for such thick blades.)

Again confirm which side of the blade has the large factory Bevel A. Hold the blade in your hand

(as if you are cutting) and if the large factory bevel is on the right side of the blade, the blade is

right handed. For the right handed blades start sharpening in the left slot of Polishing Stage 2 so

that only the beveled side (right side) of the edge will contact the polishing wheel.

Step 1 - Start In polIShIng Stage 2 (rIght handed bladeS)

Pull the full length of the blade through the left slot of Stage 2 (Figure 5) about ten (10) times

(take about 3 seconds for each pull of a 5 inch (12 cm) blade and proportionally longer for lon-

ger blades). Feel for a burr on back side of blade edge as shown in Figure 4. (The burr will be

extremely small). If there is no burr, make ten (10) additional slow pulls through the left slot. If no

burr is formed after these pulls proceed to Step 2; otherwise omit Step 2 and go to Step 3.

Step 2 – uSIng the honIng Stage 1 (rIght handed bladeS)

If you were unable to develop a burr in Stage 2 as described in Step 1 you will need to hone the

edge in Stage 1 as follows: Since your traditional blade is right handed you must hone only in

the left slot of Stage 1 (see Figure 6). The number of pulls that you need to make depends on

how dull your blade is. Duller blades will require more pulls.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Chef'sChoice Asian 316 Knivslip. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar ChefsChoice. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Chef'sChoice Asian 316 Knivslip på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Chef'sChoice Knivslipar
Fler bruksanvisningar för Knivslipar

Vanliga frågor om Chef'sChoice Asian 316 Knivslip

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Chef'sChoice Pronto 464 Knivslip

Bruksanvisning

Chef'sChoice 480KS Knivslip

Bruksanvisning

Chef'sChoice Diamond Hone 310 Knivslip

Bruksanvisning

Chef'sChoice Diamond Hone 110 Knivslip

Bruksanvisning

Chef'sChoice Manual 450 Knivslip

Bruksanvisning

Chef'sChoice Manual 440 Knivslip

Bruksanvisning

Chef'sChoice Angle Select 1520 Knivslip

Bruksanvisning

Chef'sChoice SteelPro 470 Knivslip

Relaterade kategorier