Bruksanvisning Chef'sChoice Asian 316 Knivslip

Bruksanvisning

If the knife is not yet shaving sharp, repeat steps a and b above. Again test the blade for sharp-

ness. In the event the knife still is not sufficiently sharp it will be faster to first pre-hone it in

Stage 1 as follows:

uSe honIng Stage 1, When neCeSSarY

a. Pull the blade alternately through the left and right slots (see Figure 3) of Stage 1, making about 3 pair

of pulls, taking about 3 seconds for each pull. Check the edge carefully to confirm the presence of a

burr (see Figure 4), which will be small since the Stage 1 abrasive is quite fine. To check for the burr,

move your forefinger carefully across the edge as shown in Figure 4. (Do not move your finger along

the edge—to avoid cutting your finger). If the last pull was in the right slot, the burr would appear

only on the right side of the blade (as you normally hold it) and vice versa. The burr, when present,

feels like a rough and bent extension of the edge; the opposite side of the edge feels very smooth by

comparison. When a burr exists along the entire edge, proceed to polish again in Stage 2.

b. If there is no burr continue honing in Stage 1, alternating left and right slots until a light burr develops.

When a burr is present along the entire blade length proceed as below to polish again in Stage 2.

return to polIShIng Stage 2

a. Make 3 pairs of pulls, alternating pulls in the left and right slots, taking 3 seconds per pull for a 5”

blade. Make 3 pairs of faster pulls, alternating left and right slots, taking 1 second per pull. Test the

blade for sharpness.

b. If the edge is not shaving sharp, make a few more pairs of fast pulls in Stage 2 until the edge is

shaving sharp.

re-SharpenIng the ContemporarY aSIan blade

Re-sharpen by following the procedure above starting with Polishing in Stage 2 as described.

You should be able to resharpen to a razor edge 10 or more times using only Stage 2 before

finding it necessary to again hone in Stage 1. Hone in Stage 1 only when you find it is taking too

long or too many pulls in Stage 2 to bring the edge to razor sharpness. In that event, follow the

sharpening sequence described above.

Figure 4. When you create a distinct burr along the

blade edge, it can be detected by sliding finger across

and away from the edge. Caution! See text.

5

Burr

Figure 3. Santoku knife in right slot of Stage 1.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Chef'sChoice Asian 316 Knivslip. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar ChefsChoice. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Chef'sChoice Asian 316 Knivslip på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Chef'sChoice Knivslipar
Fler bruksanvisningar för Knivslipar

Vanliga frågor om Chef'sChoice Asian 316 Knivslip

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Chef'sChoice Pronto 464 Knivslip

Bruksanvisning

Chef'sChoice 480KS Knivslip

Bruksanvisning

Chef'sChoice Diamond Hone 310 Knivslip

Bruksanvisning

Chef'sChoice Diamond Hone 110 Knivslip

Bruksanvisning

Chef'sChoice Manual 450 Knivslip

Bruksanvisning

Chef'sChoice Manual 440 Knivslip

Bruksanvisning

Chef'sChoice Angle Select 1520 Knivslip

Bruksanvisning

Chef'sChoice SteelPro 470 Knivslip

Relaterade kategorier