Bruksanvisning Lervia KH4001 Symaskin

Bruksanvisning

- 6 -

Setting the stitch length

Depending on the type of stitch you have set, it may be necessary to adjust

the stitch length appropriately to achieve the best possible sewing results.

• The numbers on the thumb wheel of the stitch length selector

6

correspond to the respective stitch length in millimeters (mm), hence,

A HIGHER NUMBER MEANS THAT THE STITCH WILL BE LONGER.

• When the stitch length selector is set at „0“

6

there will be no feeding

of the product to be sewn. This setting is used for sewing buttons on.

• The range designated with „F“ is used for the creation of so-called

satin stitches (zigzag stitches sewn very closely together). Satin stitches

can be used to sew button holes or as embroidery stitches. The appro-

priate setting within the „F“ range required for special cases is depen-

dant on the fabric and the sewing silk used. To find the respective re-

quired setting, you should first try out the stitch and stitch-length settings

on remants and, at the same time, observe the feeding characteristics,

varying the settings until the desired results have been obtained.

q

. Stitch length

w

. Direction of rotation required

to reduce stitch lengths

e

. Direction of rotation required

to increase stitch lengths

Sewing backwards

• To sew backwards, press the sewing direction reverse switch

t

as far

as it will go, keeping it pressed while simultaneously activating the foot

pedal

l

.

• To resume sewing forwards stop applying pressure to the sewing

direction reverse switch

t

, whereupon the machine will immediately

change over to sewing in a forward direction. The stitching backward

function is employed to finish off and reinforce seams.

Threading the needle and preparation

Engaging the spool

1. Tip the thread spool carrier

5

upwards and fix a spool of thread on

the carrier. Secure the spool with a thread spool holder

x

/

c

of the

appropriate size.

2. Lay the felt pad

n

on the winder spindle

8

and then place an empty

bobbin on the spindle.

3. Draw the thread through the upper thread guide

1

.

4. Wind the loose end of the thread a few times around the empty

bobbin in a clockwise direction.

5. When the first loose end windings of the thread are tautly wound

around the spool, press the spool with the winder spindle

8

against

the spool stop

9

.

6. Pull the handwheel

0

on the right side of the machine out a little

to disconnect the sewing mechanism from the motor.

7. Now switch the sewing machine on and step on the foot switch

l

.

When the bobbin is full, cut the thread.

8. Press the winder spindle

8

back to the left and remove the full spool.

9. Press the handwheel

0

back in – otherwise the sewing mechanism

of the machine will remain disconnected from the motor.

Inserting the spool

Important

Remove the power plug

k

from the wall socket!

Otherwise, the appliance could run unintentionally.

1. By turning the handwheel

0

(towards you in an anti-clockwise

direction) bring the needle into the highest possible position and

release and raise the foot with the lifting lever

g

.

2. Access the bobbin case carrier by removing the sewing table

extension

p

in the manner described above. Open the flap of the

sewing table. Remove the bobbin case by drawing its clip towards

you (flap), then remove the entire case by pulling it out from the

retaining pin towards you.

3. Unwind approximately 10 cm (4”) of the thread from the bobbin and

insert the bobbin into the bobbin case. Hold the bobbin case during

the process. Draw the thread you have unwound downwards and

then leftwards into the slit in the bobbin case, until the thread runs

into the outlet slit under the spring tab.

IB_KH4001_E2719_GB_LB3-6 22.04.2008 15:23 Uhr Seite 6

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Lervia KH4001 Symaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Lervia. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Lervia KH4001 Symaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Lervia Symaskiner
Fler bruksanvisningar för Symaskiner

Vanliga frågor om Lervia KH4001 Symaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Brother AZ17 Symaskin

Bruksanvisning

Tristar SM-6000 Symaskin

Bruksanvisning

Emerio SEW-122275.3 Symaskin

Bruksanvisning

Brother Innov-is F460 Symaskin

Bruksanvisning

Brother RH137 Symaskin

Bruksanvisning

Brother FS20s Symaskin

Bruksanvisning

Brother J14s Symaskin

Bruksanvisning

SilverCrest IAN 96965 Symaskin

Relaterade kategorier