Bruksanvisning E3 F11C Cykeldator

Bruksanvisning

Battery Installation

To help you get started quickly, the computer battery has been installed at the factory. Under

normal usage a battery should last approximately one year. The F11C uses a 3V CR2032

button cell battery, which is available at most camera and electronic shops.

NOTE: Most problems that occur with cyclocomputers are caused by a dead or weak battery.

Should you need to replace the battery, follow the steps below.

1. Remove the battery cap from the bottom of the computer using a small coin. See Figure 1.

2. Install the battery in the battery compartment with the positive (+) side facing the battery cap.

3. Reinstall the battery cap and tighten securely. NOTE: During a battery change, all data will be cleared from memory. Make a note of your

current wheel size setting and cumulative odometer mileage before replacing the battery so you can reprogram these values once the new

battery is installed (see “Program Wheel Size” and “Set the Odometer”).

4. If for some reason the screen is blank or shows an irregular display after a battery change, press the reset button on the underside of the

computer head. See Figure 6.

Determine Wheel Size

The F11C uses wheel circumference (measured in millimeters) to calculate speed and distance. Before you can program the F11C you must

calculate wheel circumference using one of the three methods below.

1. Select size from chart (least accurate): Use the chart to  nd the circumference for your tire size. The chart lists the programming sizes for some

of the most popular tire sizes currently in use. These numbers are estimations which may not precisely match the circumference of your wheel,

due to variations in tire size between brands and models.

2. Measure wheel diameter (more accurate): Measure your wheel diameter (including wheel and tire) in millimeters (1 inch = 25.4mm) and

multiply by 3.1416. This value is your wheel circumference.

F11C Cycle Computer

c

25

c

25

Thank you for your purchase of an E3™ cycle computer. With all the features that a professional rider needs to keep track of a

ride, the F11C is the perfect accessory for any cyclist. The cadence function makes the F11C an excellent choice for improving road

training as well.

1

Computer Functions

CURRENT SPEED (m/h or km/h)

Displays current speed, up to 105mph (168km/h). Accurate to 0.1m/h

or km/h. Always displayed at the top of the screen.

SPEED DISPLAY BAR

Provides a graphic display of current speed. Additional segments

of bar illuminate as current speed increases.

CLOCK (TIME)

Displays time of day in a 12 hour or 24 hour format.

AUTOMATIC RIDE TIMER (ATM)

Auto start/stop timer is activated by front wheel movement and

records actual ride time up to 9:59:59.

TRIP DISTANCE (DST)

Displays distance traveled during current ride (or since last reset),

up to 999.9 mi. or km.

ODOMETER (ODO)

Displays cumulative ride distance, up to 99,999 mi. or km.

SPEED COMPARISON (56)

Compares current speed to average speed. As you ride, a (5) or (6)

will appear next to current speed to indicate whether

your current speed is above (5) or below (6) your average speed.

This function is automatic, requires no programming and

cannot be disabled.

AVERAGE SPEED (AVG)

Calculates average speed based on ride time (ATM) & trip distance (DST).

MAXIMUM SPEED (MAX)

Displays highest speed attained during a ride (or since last reset), up to

105m/h (168km/h).

STOPWATCH (STP)

Manual stopwatch allows you to time any portion of a ride, up to 9:59:59.

CADENCE (C)

Displays crank revolutions per minute (RPM) from 30 to 240.

DUAL WHEEL SIZE SETTINGS

Wheel circumference is used to calculate speed and distance. The F11C

includes two wheel size settings (

1 and 2 ), allowing you to switch your

computer between two bikes with di erent wheel sizes (e.g. your road

bike and mountain bike).

AUTO SLEEP

To prolong battery life, the F11C will automatically enter “sleep” mode

after 5 minutes of non-use. The computer will automatically restart as

soon as it receives input from the speed sensor, or when any button is

pressed.

SCAN MODE

Allows hands free viewing of all display screens except Cadence. When

scan mode is activated, the computer will scroll through all display

screens (except Cadence) on a continuous loop, displaying each screen

for two seconds. To activate scan mode, press and hold the LEFT button

for three seconds in any display screen except Cadence. To exit scan

mode, press the LEFT or RIGHT button in any display screen.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din E3 F11C Cykeldator. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar E3. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din E3 F11C Cykeldator på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för E3 Cykeldatorer
Fler bruksanvisningar för Cykeldatorer

Vanliga frågor om E3 F11C Cykeldator

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

E3 F8 Cykeldator

Bruksanvisning

E3 FX10 Cykeldator

Bruksanvisning

Serfas SI-30 Cykeldator

Bruksanvisning

Crivit IAN 292844 Cykeldator

Bruksanvisning

Crivit IAN 56074 Cykeldator

Bruksanvisning

XLC CY-312B Cykeldator

Bruksanvisning

BBB BCP-55 DigiSpeed Cykeldator

Bruksanvisning

Bikehut 151657 11 Function Cykeldator

Relaterade kategorier