Bruksanvisning Black and Decker KS603E Sticksåg

Bruksanvisning

7

ENGLISH

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

#

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features:

1. On/off switch

2. Lock-on button

3. Dust extraction outlet

4. Shoe plate

5. Saw blade support roller

Fig. E

6. Saw blade storage compartment (KS602E & KS603E)

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped. Used saw blades may be hot.

Adjustingthesawbladesupportroller(g.A&B)

u Loosen the two screws (8).

u Push the blade support roller (5) forward until it touches

the back edge of the saw blade (7).

u Tighten the two screws (8).

Fittingandremovingthesawblade(g.C)

u Before tting or removing the saw blade (7) the saw blade

support roller (5) must be adjusted to the rear position so

that it does not contact the blade.

u Loosen (do not remove) the two screws (10).

u Hold the saw blade (7) with the teeth facing forward.

u Insert the shank of the saw blade (7) into the blade holder

(9) as far as it will go.

u Slightly tighten the two screws (10) alternately to position

the blade, then fully tighten the two screws (10).

u Adjust the saw blade support roller (5) as described above.

u To remove the saw blade (7), turn both screws (10) one

turn counter-clockwise.

Connectingavacuumcleanertothetool(g.D)

An adaptor (11) is required to connect a vacuum cleaner or

dust extractor to the tool. The adaptor can be purchased from

your local Black & Decker retailer.

u Push the adaptor (11) into the dust extraction outlet (3).

u Connect the vacuum cleaner hose (12) to the adaptor (11).

Sawbladestorage(KS602E&KS603Eonly)(g.E)

Saw blades (7) can be stored in the storage compartment (6)

located on the side of the tool

u Open the cover of the saw blade storage compartment (6)

by holding the tab on the top of the door and pulling outwards.

u Remove or store saw blades (7) in the storage

compartment (6).

u Close the cover of the saw blade storage compartment (6)

and make sure that it is latched closed.

Cutlineblower(g.F)

u To aid visibility when cutting, your jigsaw is equipped with

a cut line blower (13) which will keep the work area clear

of dust as you saw.

Use

Adjustingtheshoeplateforbevelcuts(g.G)

The shoe plate can be set to make either a straight cut or a

left or right bevel cut at an angle of 45°.

u Loosen the screws (8).

u Pull the shoe plate (4) forward, rotate the shoe plate (4) to

the left or right and push it back into the 45° location.

u Push the blade support roller (5) forward until it touches

the saw blade (7).

u Tighten the screws (8).

To reset the shoe plate for straight cuts:

u Loosen the screws (8).

u Pull the shoe plate (4) forward, rotate to the centre and

push it back into the 0° location.

u Push the blade support roller (5) forward until it touches

the saw blade (7).

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Black and Decker KS603E Sticksåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Black and Decker. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Black and Decker KS603E Sticksåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Black and Decker Sticksågar
Fler bruksanvisningar för Sticksågar

Vanliga frågor om Black and Decker KS603E Sticksåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Black and Decker XTS10EK Sticksåg

Bruksanvisning

Black and Decker KS455 Sticksåg

Bruksanvisning

Black and Decker KS800EW Sticksåg

Bruksanvisning

Black and Decker KS800E Sticksåg

Bruksanvisning

Black and Decker KS601E Sticksåg

Bruksanvisning

Black and Decker KS702PE Sticksåg

Bruksanvisning

Black and Decker KS777 Sticksåg

Bruksanvisning

Black and Decker KS600E Sticksåg

Relaterade kategorier