Bruksanvisning Black and Decker BD146F3 Borrskruvdragare

Bruksanvisning

power on jobs that were easily done before.

When charging the battery for the first time, or

after prolonged storage, it will only accept an

80% charge. After several charge and discharge

cycles, the battery will attain full capacity. The

battery may become warm while charging; this

is normal and does not indicate a problem.

Warning! Do not charge the battery at ambi -

ent temperatures below 4

o

C or above 40

o

C.

Recommended charging temperature: approx.

24

o

C.

Using the 3hr charger

- To charge the battery (7), remove it from the

tool and insert it into the charger (8). The battery

will only fit into the charger in one way. Do not

force. Be sure that the battery is fully seated in

the charger.

- Plug in the charger.

- Check the red charging indicator (9) lights

up.

Allow approximately 3 hours for the battery to

fully charge.

- Remove the battery from the charger.

- Unplug the charger

Selecting the direction of rotation (fig. 3)

For drilling and for tightening screws, use

forward (clockwise) rotation. For loosening

screws or removing a jammed drill bit, use

reverse (counterclockwise) rotation.

- To select forward rotation, push the forward/

reverse slider (2) to the left.

- To select reverse rotation, push the forward/

reverse slider to the right.

- To lock the tool, set the forward/reverse slider

into the centre position.

Selecting the operating mode or torque (fig. 4)

This tool is fitted with a collar to select the

operating mode and to set the torque for tighten-

ing screws. Large screws and hard workpiece

materials require a higher torque setting (larger

numbers on collar) than small screws and soft

workpiece materials. The collar has a wide range

of settings to suit your application.

- For drilling in wood, metal and plastics, set the

collar (4) to the drilling position by aligning the

symbol

with the marking (13).

- For screwdriving, set the collar to the desired

setting. If you do not yet know the appropriate

setting, proceed as follows:

- Set the collar (4) to the lowest torque setting.

- Tighten the first screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the

correct setting. Use this setting for the remaining

screws.

BD128F3/BD148F3/BD188F3 - Drilling in

masonry (fig. 4&5)

- For drilling in masonry, set the collar (3) to the

hammer drilling position by aligning the symbol

with the marking (13).

- Slide the two-gear selector (5) towards the

front of the tool (2nd gear).

Two-gear selector (fig. 5)

- For drilling in steel and for screwdriving appli -

cations, slide the two-gear selector (5) towards

the rear of the tool (1st gear).

- For drilling in materials other than steel, slide

the two-gear selector (5) towards the front of the

tool (2nd gear).

Removable Chuck with Quick Connect

TM

Bit

Change System - Figure 8 (BD126F3/BD146F3

only)

Another unique feature of your drill is the ability

to remove the chuck quickly and easily.

This allows for a drill bit to be in the keyless

chuck, while another accessory such as a

screwdriver bit, can be inserted into the Quick

Connect

TM

hex shaft at the same time.

To remove the chuck:

1. Grasp the drill and depress the two orange

buttons on the chuck collar as shown in Figure 8

2. With the buttons depressed, pull straight out.

To replace the chuck:

1. Push the quick connect chuck straight on with

a slight twisting motion until you hear it click into

7

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Black and Decker BD146F3 Borrskruvdragare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Black and Decker. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Black and Decker BD146F3 Borrskruvdragare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Black and Decker Borrskruvdragare
Fler bruksanvisningar för Borrskruvdragare

Vanliga frågor om Black and Decker BD146F3 Borrskruvdragare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Black and Decker BDCDD12USB Borrskruvdragare

Bruksanvisning

Black and Decker KC1451CN Borrskruvdragare

Bruksanvisning

Black and Decker BCD001 Borrskruvdragare

Bruksanvisning

Black and Decker KC1261F Borrskruvdragare

Bruksanvisning

Black and Decker BDCDMT108 Borrskruvdragare

Bruksanvisning

Black and Decker EPC148V Borrskruvdragare

Bruksanvisning

Black and Decker HP12KD Borrskruvdragare

Bruksanvisning

Black and Decker HP14KD Borrskruvdragare

Relaterade kategorier