Bruksanvisning Ardo BH40AVX Häll

Bruksanvisning

-

These instructions are intended for qualified technicians.

-

The appliance must be installed correctly, in compliance with current laws.

-

Before carrying out any operation on the appliance, it must be disconnected from the electric supply.

Fitting the appliance in the worktop

The cooktop may be fitted into any worktop, as long as it is heat resistant (minimum temperature of 90°C)

The dimensions of the hole to be made in the worktop and the minimum distances between rear

and side walls and those above the appliance are shown in figure 4.

Isolation below (fig.6):

-

If the cooktop is installed without an oven below it, a separator panel must be placed between

the bottom of the cooktop and the housing below it, at a minimum distance of 10 mm.

-

If the cooktop is installed over an oven, place a separator panel at a minimum distance of 15mm

and follow the oven manufacturer's instructions, ensuring nonetheless sufficient aeration

as specified in fig.6.

In any event, the electrical connection of the two appliances must be carried out

separately,

both for electrical safety and to facilitate removal.

It is advisable to use an oven equipped with an internal forced cooling system.

Fixing the cooktop (fig.7):

To fix the cooktop in the housing, proceed as follows:

-

Position the special gasket supplied [C] along the outer perimeter of the worktop, following the

diagram shown in fig.4, so that the ends of the gasket meet exactly without overlapping.

-

Position the cooktop into the worktop, taking care to ensure it is placed exactly in the centre.

-

Fix the cooktop to the worktop using the special brackets supplied [A], as shown in fig.7.

Correct installation of the sealing gasket ensures complete protection against infiltration of liquids.

Installation area and removal of combustion fumes

The appliance must be installed and operated in suitable areas, and in compliance with current laws.

The installation technician must observe current laws governing ventilation and removal of combustion fumes

Please remind that the air required for combustion is 2m

3

/h per kW of power (gas) installed.

Installation area

In the room where the gas appliance is installed, there must be a sufficient natural air supply to

allow the gas to burn correctly (in conformity of currents laws).

The natural flow of air must take place through an opening made on an outside wall of the room

and having a working section of at least 100 cm

2

(A). In the case of appliances without safety

valves, this opening must have a minimum working section of 200 cm

2

(fig.8).

This opening must be made in such a way that it cannot be obstructed from inside or outside.

It should be positioned near floor level, preferably on the side opposite the fume exhaust devices.

If it is not possible to make the necessary openings, the air can be supplied from an adjacent, suitably

ventilated room, as long as this room is not a bedroom, a dangerous area or a lowpressure area.

Removal of combustion fumes

Combustion fumes produced by gas appliances must be removed by means of a hood connected

directly either to an exhaust duct or to the outside (fig.8).

If a hood cannot be installed, an electric extractor fan must be fitted to the outside wall or the window.

This electric extractor fan must have a sufficient capacity to guarantee a change of air of the

kitchen of at least 3-5 times its volume.

Components shown in fig.8:

A

Opening for air supply

C

Hood for exhaust removal of combustion fumes

E

Electric extractor fan for removal of combustion fumes

INSTALLATION INSTRUCTIONS

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Ardo BH40AVX Häll. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Ardo. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Ardo BH40AVX Häll på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Ardo Hällar
Fler bruksanvisningar för Hällar

Vanliga frågor om Ardo BH40AVX Häll

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Ardo PFS32GVX Häll

Bruksanvisning

Ardo HBF6V4GTI Häll

Bruksanvisning

Ardo PFS4030VX Häll

Bruksanvisning

Ardo FL6V4GTX Häll

Bruksanvisning

Ardo PLT6040VX Häll

Bruksanvisning

Ardo FL75GTX Häll

Bruksanvisning

Ardo F6V4X Häll

Bruksanvisning

Ardo HBF6V4GTB Häll

Relaterade kategorier