Bruksanvisning Sealey SMS01 Borrslipare

Bruksanvisning

INSTRUCTIONS FOR

DRILL BIT SHARPENER GRINDING

ATTACHMENT

MODEL NO: SMS01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

 WARNING! Disconnect the grinder from the mains power, and ensure the grinding wheels are at a standstill before attempting to

position drill bit.

9 Maintain the sharpener in good condition.

9 Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.

▲ DANGER! DO NOT use a damaged grinding wheel, to sharpen drill bits.

9 Ensure that the correct grinding wheel is used for sharpening of drill bits.

 WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.

A guard or any other part that is damaged should be repaired or replaced before tool is next used. The eye shields are a mandatory

fitting when grinder is used in premises covered by the Health & Safety at Work Act.

9 Ensure adequate lighting.

9 Before each use check grinding wheels for condition. If worn or damaged replace immediately.

 WARNING! Always wear approved eye or face protection when operating a grinder.

9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

9 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.

9 Keep children and unauthorised persons away from the working area.

8 DO NOT use the sharpener for a task it is not designed to perform.

8 DO NOT operate the grinder if any parts are damaged or missing as this may cause failure and/or personal injury.

8 DO NOT switch on the grinder whilst the wheel is in contact with the drill bit.

8 DO NOT use grinder where there are flammable liquids, solids or gases, such as paint solvents and including waste wiping or cleaning rags

etc.

8 DO NOT touch the drill bit close to the ground surface as it will be very hot. Allow to cool. The drill bit may also be very sharp.

8 DO NOT sharpen drill bits when you are tired, under the influence of alcohol, drugs or intoxicating medication.

9 When not in use switch off the grinder, disconnect from the mains power supply and clean the machine and working area.

2. INTRODUCTION

Ideal for use with any standard bench grinder, the grinding attachment provides quick and precise sharpening of 3-19mm (1/8-3/4”) HSS twist

drill bits with a 75mm minimum length. Features an angle gauge with pre-sets at 41° (Countersink), 49°, 59°, 68° and 88°. Also features a

rotating neck which aids grinding both sides of the drill bit. Perfect for use in any workshop or garage.

3. SPECIFICATION

Model No: ................................................................... SMS01

Sizes: ........................................................ 3-19mm (1/8-3/4”)

Angle Adjustment: .........41° (Countersink), 49°, 59°, 68°, 88°

Minimum Drill Bit Length: ............................................. 75mm

4. ASSEMBLY

4.1.  Thejigmustbesecurelyxedinpositionusingabolt,

washers and nut. Varying positions in relation to the

grinding wheel can be obtained using the slot in the

 base.(g1)

4.2. The jig must be positioned so that the top of the trough

can be brought to the face of the wheel.

SMS01 | Issue 1 20/12/17

Original Language Version

© Jack Sealey Limited

Refer to

instructions

g.1

Wear eye

protection

Wear a mask

Wear ear

protection

Wear safety

footwear

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Sealey SMS01 Borrslipare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Sealey. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Sealey SMS01 Borrslipare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Sealey Borrslipare
Fler bruksanvisningar för Borrslipare

Vanliga frågor om Sealey SMS01 Borrslipare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Sealey SMS2001M Borrslipare

Bruksanvisning

Drill Doctor 350X Borrslipare

Bruksanvisning

Multi-Sharp 30-6532 Borrslipare

Bruksanvisning

Holzmann BSG 13E Borrslipare

Bruksanvisning

Parkside PBSG 95 C4 Borrslipare

Bruksanvisning

Drill Doctor 360X Borrslipare

Bruksanvisning

Bosch S 41 Borrslipare

Bruksanvisning

Parkside IAN 108189 Borrslipare

Relaterade kategorier