Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by taking
proper precautions as given below.
■ Maintain a firm grip with both hands on the power tool
and position your body and arms to allow you to resist
kickback forces. Always use auxiliary handle, if provided,
for maximum control over kickback or torque reaction
during start-up. The operator can control torque reactions or
kickback forces, if proper precautions are taken.
■ Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
■ Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool
in direction opposite to the wheel’s movement at the point of
snagging.
■ Use special care when working corners, sharp edges,
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
■ Do not attach a saw chain woodcarving blade,
segmented diamond wheel with a peripheral gap
greater than 10 mm or toothed saw blade. Such blades
create frequent kickback and loss of control.
Safety Warnings specific for Sanding Operations
■ Use proper sized sanding disc paper. Follow
manufacturers recommendations, when selecting
sanding paper. Larger sanding paper extending too far
beyond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc or kickback.
Safety Warnings specific for Polishing Operations
■ Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely. Tuck
away or trim any loose attachment strings. Loose
and spinning attachment strings can entangle your
fingers or snag on the workpiece.
Additional safety warnings
■ Clamp workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
■ Injuries may be caused, or aggravated, by prolonged use of
a tool. When using any tool for prolonged periods, ensure
you take regular breaks.
■ Ambient temperature range for tool during operation is
between 0°C and 40°C.
■ Ambient temperature range for tool storage is between 0°C
and 40°C.
■ The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
■ The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the product.
■ To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
■ Ambient temperature range for battery during use is
between 0°C and 40°C.
■ Ambient temperature range for battery storage is
between 0°C and 20°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 83.
1. Hi-Lo speed switch
2. Spindle lock button
3. Side handle socket
4. Spindle
5. Trigger lock switch
6. Trigger
7. Handle, insulated gripping surface
8. LED light
9. Battery port
10. Operator’s manual
11. Side handle
12. 2” Sandpaper 400 / 800 / 1200 /1500 / 2000 grit
13. 3” Wool elastic bonnet
14. 3” Black polishing foam pad
15. 3” Yellow polishing foam pad
16. 3” Polishing back pad
17. 2” Hoop-and-loop pad
18. 2” Sanding back pad
19. Compound/scratch remover
20. Microfibre cloth
21. Battery pack
22. Charger
MAINTENANCE
■ The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product from the power
supply will prevent accidental starting that could cause
serious injury.
■ When servicing, use only original manufacturer’s
replacement parts, accessories and attachments. Use
of any other parts may create a hazard or cause product
damage.
■ Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
■ Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
■ For greater safety and reliability, all repairs should be
performed by an authorised service centre.
4
Original Instructions
Delta i konversationen om denna produkt
Här kan du dela vad du tycker om Ryobi RDP18-0 Polermaskin. Om du har en fråga, läs först noggrant igenom manualen. Att begära en manual kan göras genom att använda vårt kontaktformulär.