Bruksanvisning RIDGID R4210 Kapsåg

Bruksanvisning

4 - English

MITER SAW SAFETY RULES

Always use a clamp or a fixture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to bite and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

If the workpiece or blade becomes jammed, turn the

mitre saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/or re-

move the battery pack. Then work to free the jammed

material. Continued sawing with a jammed workpiece

could cause loss of control or damage to the mitre saw.

After finishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Hold the handle firmly when making an incomplete cut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may to be suddenly pulled downward, causing

a risk of injury.

 Save these instructions. Refer to them frequently and

use to instruct other users. If you loan someone this tool,

loan them these instructions also.

ADDITIONAL SAFETY RULES

 Use the proper extension cord. Make sure your extension

cord is in good condition. Use only a cord heavy enough

to carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. A wire gauge size (A.W.G.) of at

least 14 is recommended for an extension cord 25 feet

or less in length. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

 Inspect tool cords periodically. If damaged, have

repaired by a qualified service technician at an authorized

service facility. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 Inspect extension cords periodically and replace if

damaged.

 Polarized plugs. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

 Know your power tool. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the specific potential hazards related to this tool.

 Always wear eye protection with side shields which

is marked to comply with ansi Z87.1 when using this

product. Failure to do so could result in objects being

thrown into your eyes, resulting in possible serious injury.

 Never stand on tool. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

 Keep guards in place and in good working order.

 Use the right direction of feed. Feed work into a blade,

cutter, or sanding spindle against the direction of rotation

of the blade, cutter, or sanding spindle only.

 Never leave tool running unattended. Turn the power

off. Don’t leave tool until it comes to a complete stop.

 Use only correct blades. Do not use blades with incorrect

size holes. Never use blade washers or blade bolts that

are defective or incorrect. The maximum blade capacity

of your saw is 10 in.

 Before making a cut, be sure all adjustments are

secure.

 Never touch blade or other moving parts during use.

 Double check all setups. Make sure blade is tight and not

making contact with saw or workpiece before connecting

to power supply.

 Firmly clamp or bolt your tool to a workbench or table

at approximately hip height.

 Make sure the miter table and saw arm (bevel

function) are locked in position before operating

your saw. Lock the miter table by pushing the

miter lock lever down. Lock the saw arm (bevel

function) by securely tightening the bevel lock knob.

 Never move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade

is rotating. Any slip can result in contact with the blade

causing serious personal injury.

 Avoid awkward operations and hand positions where a

sudden slip could cause your hand to move into the blade.

ALWAYS make sure you have good balance. NEVER

operate your miter saw on the floor or in a crouched

position.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din RIDGID R4210 Kapsåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar RIDGID. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din RIDGID R4210 Kapsåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för RIDGID Kapsågar
Fler bruksanvisningar för Kapsågar

Vanliga frågor om RIDGID R4210 Kapsåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

RIDGID R41221 Kapsåg

Bruksanvisning

RIDGID R4122 Kapsåg

Bruksanvisning

Skil 1310 AA Kapsåg

Bruksanvisning

Graphite 59G806 Kapsåg

Bruksanvisning

Makita LS1017L Kapsåg

Bruksanvisning

Far Tools JR 211C Kapsåg

Bruksanvisning

Bosch GCM 10 MX Professional Kapsåg

Bruksanvisning

Parkside PZKS 2000 B2 Kapsåg

Relaterade kategorier