Bruksanvisning RIDGID R4210 Kapsåg

Bruksanvisning

3 - English

GENERAL SAFETY RULES

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Sparks from abrasive cutting will

burn the lower guard, the kerf insert and other plastic

parts.

Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut ”freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down

and push the saw through the workpiece. Cutting on

the pull stroke is likely to cause the saw blade to climb

on top of the workpiece and violently throw the blade

assembly towards the operator.

Never cross your hand over the intended line of cut-

ting either in front or behind the saw blade. Supporting

the workpiece ”cross handed” i.e. holding the workpiece

to the right of the saw blade with your left hand or vice

versa is very dangerous.

Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no

nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small de-

bris or loose pieces of wood or other objects that contact

the revolving blade can be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

Ensure the mitre saw is mounted or placed on a level,

firm work surface before use. A level and firm work sur-

face reduces the risk of the mitre saw becoming unstable.

Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will not

interfere with the blade or the guarding system. With-

out turning the tool ”ON” and with no workpiece on the

table, move the saw blade through a complete simulated

cut to assure there will be no interference or danger of

cutting the fence.

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or longer

than the table top. Workpieces longer or wider than the

mitre saw table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling

you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If confined,

i.e. using length stops, the cut-off piece could get wedged

against the blade and thrown violently.

MITER SAW SAFETY RULES

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din RIDGID R4210 Kapsåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar RIDGID. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din RIDGID R4210 Kapsåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för RIDGID Kapsågar
Fler bruksanvisningar för Kapsågar

Vanliga frågor om RIDGID R4210 Kapsåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

RIDGID R41221 Kapsåg

Bruksanvisning

RIDGID R4122 Kapsåg

Bruksanvisning

Skil 1310 AA Kapsåg

Bruksanvisning

Graphite 59G806 Kapsåg

Bruksanvisning

Makita LS1017L Kapsåg

Bruksanvisning

Far Tools JR 211C Kapsåg

Bruksanvisning

Bosch GCM 10 MX Professional Kapsåg

Bruksanvisning

Parkside PZKS 2000 B2 Kapsåg

Relaterade kategorier