Bruksanvisning RIDGID R41221 Kapsåg

Bruksanvisning

4 - English

GENERAL SAFETY RULES

 INSPECT TOOL CORDS PERIODICALLY. If damaged,

have repaired by a qualified service technician at an

authorized service facility. Repair or replace a damaged

or worn cord immediately. Stay constantly aware of cord

location and keep it well away from the rotating blade.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 POLARIZED PLUGS. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than

the other). This plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a qualified electrician

to install the proper outlet. Do not change the plug in any

way.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or

any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 USE ONLY CORRECT BLADES. Do not use blades with

incorrect size holes. Never use blade washers or blade

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 12 in.

 BEFORE MAKING A CUT, BE SURE ALL ADJUST-

MENTS ARE SECURE.

 BE SURE BLADE PATH IS FREE OF NAILS. Inspect for

and remove all nails from lumber before cutting.

 NEVER TOUCH BLADE or other moving parts during

use.

NEVER START A TOOL WHEN ANY ROTATING

COMPONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed in

this manual or addendums. Use of accessories that are not

listed may cause the risk of personal injury. Instructions for

safe use of accessories are included with the accessory.

 DOUBLE CHECK ALL SETUPS. Make sure blade is tight

and not making contact with saw or workpiece before

connecting to power supply.

SPECIFIC SAFETY RULES

 FIRMLY CLAMP OR BOLT your tool to a workbench or

table at approximately hip height.

 KEEP HANDS AWAY FROM CUTTING AREA. Do not

reach underneath work or in blade cutting path with your

hands and fingers for any reason. Always turn the power

off.

 ALWAYS SUPPORT LONG WORKPIECES while cutting

to minimize risk of blade pinching and kickback. Saw may

slip, walk or slide while cutting long or heavy boards.

 ALWAYS USE A CLAMP to secure the workpiece when

possible.

 BE SURE THE BLADE CLEARS THE WORKPIECE.

Never start the saw with the blade touching the workpiece.

Allow motor to come up to full speed before starting cut.

 MAKE SURE THE MITER TABLE AND SAW ARM

(BEVEL FUNCTION) ARE LOCKED IN POSITION

BEFORE OPERATING YOUR SAW. Lock the miter table

by pushing the miter lock lever down. Lock the saw arm

(bevel function) by securely tightening the bevel lock knob.

 NEVER USE A LENGTH STOP ON THE FREE SCRAP

END OF A CLAMPED WORKPIECE. NEVER hold onto or

bind the free scrap end of the workpiece in any operation.

If a work clamp and length stop are used together, they

must both be installed on the same side of the saw table to

prevent the saw from catching the loose end and kicking

up.

 NEVER cut more than one piece at a time. DO NOT

STACK more than one workpiece on the saw table at a

time.

 NEVER PERFORM ANY OPERATION FREEHAND.

Always place the workpiece to be cut on the miter table

and position it firmly against the fence as a backstop.

Always use the fence.

 NEVER hand hold a workpiece that is too small to be

clamped. Keep hands clear of the cutting area.

 NEVER reach behind, under, or within three inches of the

blade and its cutting path with your hands and fingers for

any reason.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din RIDGID R41221 Kapsåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar RIDGID. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din RIDGID R41221 Kapsåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för RIDGID Kapsågar
Fler bruksanvisningar för Kapsågar

Vanliga frågor om RIDGID R41221 Kapsåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

RIDGID R4122 Kapsåg

Bruksanvisning

RIDGID R4210 Kapsåg

Bruksanvisning

Parkside PKS 1700 A1 Kapsåg

Bruksanvisning

DeWalt DCS785B Kapsåg

Bruksanvisning

Power Craft 48000 Kapsåg

Bruksanvisning

Skil 1320 AA Kapsåg

Bruksanvisning

FERM MSM1040 Kapsåg

Bruksanvisning

Hikoki C 8FSE Kapsåg

Relaterade kategorier