Bruksanvisning Rexel LP25HS Lamineringsmaskin

Bruksanvisning

Operating Instructions

LP 25HS (A4) LP 35HS (A3)

A. Power Switch / Reverse Switch

B ‘On’ light

C. ‘Ready’ light

D. Pouch/temperature setting

E. Entry Slot

F. Entry Guides

G. Exit slot

H. Release button

IMPORTANT SAFEGUARDS

When using electrical appliances, basic

precautions should always be followed to reduce

the risk of electric shock and injury, including the

following:

1. Carefully read all instructions

2. Always unplug the appliance when not in use

or before cleaning.

3. Extreme caution to be taken when appliance

is used by, or near to, children or invalids.

4. To protect against risk of electrical hazards,

do not immerse power cord, plug, or

appliance in water or other liquids.

5. Do not insert any metal objects, e.g. scissors,

or foreign objects into the entry or exit areas

of the machine. Do not laminate metallic

objects.

6. Do not operate the appliance with a damaged

power cord or plug, or after the appliance

malfunctions, has been dropped or is

damaged in any manner.

7. The plug on the power cord is the disconnect

device.

8. The equipment should be installed near the

outlet socket and the socket should be easily

accessible.

OPERATION

Before you use your LP Laminating machine for

the first time, it is recommended that you

familiarise yourself with the machine’s operation

and controls. Check the results using a range of

sample sheets of paper before laminating your

valuable original documents.

IMPORTANT

1. It is important that you do not use a Carrier

with this machine. This can result in the

laminator becoming jammed or failing to run.

This is an operator fault and is not covered

by a manufacturer’s warranty. (A carrier is

made from folded card and is supplied with

most packs of pouches).

2. Do not attempt to laminate items which are

too thick for your laminator i.e. the total

thickness including the pouch must not

exceed 1.0mm.

HOT LAMINATING

1. Plug the laminator into a convenient power

socket

2. Switch on the power switch ( I ) , the Red

light will illuminate to indicate that the power

is on

3. Select the appropriate temperature/pouch

setting for the thickness of pouch.

4. The laminator will pre-heat for approximately

3-4 minutes.

5. Whilst the laminator is pre heating, you can

prepare your item to be laminated by placing

it centrally into the correct sized pouch,

leaving the sealed edge intact.

6. When the required temperature is reached the

Green light will come on.

7. Gently insert the pouch, sealed edge first,

squarely between the entry guides into the

front of the laminator until it engages with

automatic feed rollers.

8. The pouch will move through the unit and exit

at rear.

9. During the laminating process the Green light

may go off as heat is absorbed by the

laminate. Always wait until the Green light is

on before laminating your next document.

10. Always turn your laminator OFF after use. (O).

REVERSE FUNCTION

CAUTION: Do not try to force the pouch

into the laminator or try to pull the pouch out.

This will damage (and could break) the laminator

as well as not allowing for proper processing of

the laminating pouch.

There is a reverse feature included on the on/off

button (A) of the machine. If you need to retrieve

a document during lamination:

1. Press the reverse button.

2. With the other hand gently hold the pouch

and document.

3. If the pouch has gone completely into the

machine and is not sticking out of the front or

back, there is nothing you can do. Do not try

to open the machine. This can be dangerous

and will invalidate the warranty.

PHOTO LAMINATING

1. Your Rexel LP Laminator will laminate

photographs without the need for special

pouches. Photographs have a sealed plastic

surface that can produce disappointing

results on some laminators as the adhesive

will show as bubbles on the surface of the

photograph.

2. Heavily coloured inkjet copies and varnished

printed pages will also have excellent results

on this laminator with standard pouches.

COLD LAMINATING

1. Select cold setting on the temperature dial.

2. Use ‘cold’ or ‘self-seal’ pouches

3. Remember, when the machine is cold the

temperature is correct to process ‘cold’ or

‘self-seal’ pouches. The green ready light

does not illuminate for the cold setting.

CAUTION: Remember if you have been hot

laminating and then wish to Cold laminate the

machine will have to cool for at least 1 hour

before laminating can commence. Never use

‘self-seal’ pouches on a hot setting, as they will

be spoilt along with the document inside.

HELPFUL HINTS

1. The hot lamination process achieves the

required result by bonding into the surface of

your document. Once you have laminated

your document it cannot be retrieved

2. Do not attempt to hot laminate heat sensitive

documents such as thermal paper, wax

based inks etc.

3. If the laminated document has a milky

appearance, you may need to process it

again at a higher temperature

4. If the laminated document is ridged and hard

it has probably been laminated too hot, and

you should put other laminates through at a

lower setting.

5. If in doubt, start at a lower temperature and if

the laminate does not bond to the document

(appears cloudy) then repeat using a higher

temperature.

6. If air pockets develop during processing, use

a small sharp needle or pin to gently

puncture pockets and process again.

7. Do not handle the inside of the laminating

pouch moisture from your hands could impair

the processing quality.

CARE AND CLEANING

This personal laminator is for low volume use

only. No servicing other than external cleaning

should be performed on the machine. Do not

immerse in water.

To reduce risk of electric shock, do not

remove the base.

• Never clean with scouring powders or hand

implements.

• Wipe clean with a soft cloth

SERVICE AND REPAIRS

Do not attempt to repair the machine

yourself as there are no serviceable

components within the machine.

Never open up the machine

Repair should only be carried out by an

authorised service representative.

TECHNICAL SPECIFICATION

WARRANTY

This machine is guaranteed for 24 months from

the date of purchase – Rexel will repair or replace

the laminator at their discretion

This does not affect your statutory rights.

Please contact your supplier if you experience

any problems.

Technical Specifications

Model LP25HS LP35HS

Maximum Pouch Size A4 /9" A3 / 12"

Minimum Pouch Size Credit card size (54x86mm)

Maximum Pouch Pouch sizes up to A7 =

Thickness 2 x180 (360) micron / 7 mil

Maximum Pouch Pouch sizes above A7 =

Thickness 2 x180 (360) micron / 7 mil

Power Supply 230V 115V 230V 115V

50Hz 60Hz 50Hz 60Hz

Maximum Power 600W 600W 650W 600W

Consumption

Weight 5.2 kg 6.4 kg

Packed Weight 6.29 kg 7.49 kg

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Rexel LP25HS Lamineringsmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Rexel. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Rexel LP25HS Lamineringsmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Rexel Lamineringsmaskiner
Fler bruksanvisningar för Lamineringsmaskiner

Relaterade produkter

Bruksanvisning

Rexel LV340HS Lamineringsmaskin

Bruksanvisning

Rexel LV250HS Lamineringsmaskin

Bruksanvisning

Rexel Style A3 Lamineringsmaskin

Bruksanvisning

Rexel LP35HS Lamineringsmaskin

Bruksanvisning

Rexel Style A4 Lamineringsmaskin

Bruksanvisning

Hama KHL46 Lamineringsmaskin

Bruksanvisning

Lervia KH 4410 Lamineringsmaskin

Bruksanvisning

Leitz iLAM Home Office A4 Lamineringsmaskin

Relaterade kategorier