Bruksanvisning Remington DA-57 Rakapparat

Bruksanvisning

■ Every six months, lubricate the trimmer

teeth by applying a drop of light machine

oil one-third and two-thirds of the way along

the blade. Using your finger tip, spread the

oil along the teeth, and run the trimmer for a

few seconds.

Replacing Foils and Cutters

Because they are subject to daily use, the cutters and foils of your

R e m i n g t o n

®

MicroScreen

®

2 Shaver will wear and eventually re q u i re

replacement to maintain a close, comfortable shave. Depending on your

shaving technique and habits, the foils will usually last six months; the

cutters, one year. Model DA-757 has a foil replacement indicator.

The foil icon on the LCD display will flash when the foil is due for

replacement. Some signs that your foils and cutters need replacing are :

■ Irritation. As foils get worn, you may notice your skin feeling

sensitive after a shave, particularly when you apply aftershave.

■ Pulling. As cutters wear, your shave may not feel as close, and you

may feel your shaver is pulling at your whiskers.

■ Wear-through. You may notice that the cutters have worn through

the foil.

To order replacement foils and cutters, call 1-800-736-4648.

To prevent inadvertent damage to the Foils and Cutter Assembly,

do not attempt to remove them unless you are replacing them. To

remove the old foil and cutters follow the instructions that come with the

foil and cutter replacement package. It's always a good idea to replace

the foils when you replace the Cutter Assembly.

To Replace a Cutter Assembly That is Removed

Unintentionally:

■ Hold the assembly in the middle of the "T."

■ Gently place the forked legs into the open-

ing at the top of the oscillator tips.

■ Do not push downward on the ends of the

cutters, as you may bend the cutter, reducing

its ability to operate smoothly.

■ Do not remove cutters from the plastic

pieces to which they are attached, as you may

damage the assembly.

Removing the Headguard

Before operating your

MicroScreen

®

2 Shaver, remove

the Headguard, which protects

the Foils and Cutter Assembly.

It is important to remove the

Headguard correctly to avoid

damaging the clips that hold

it firmly to the shaver.

■ Press lightly on the top of the Headguard.

■ Lift the lower rear edge.

■ Pull the Headguard away from the shaver.

Operation

Use of a shaver at voltages other than the ones

specified below will damage it and void the warranty.

Model DA-57, DA-107 - Corded Shavers 120 Volts A.C.

Model DA-307, DA-325 - Rechargeable Shaver

World-wide A.C.voltage:105-130 Volts A.C.

at 60 Hz,and 105-240 Volts,A.C. at 50 Hz.

Model DA-407 - Cord/Cordless Shaver World-wide A.C.

voltage:100-240 Volts A.C.,50-60 Hz.

Model DA-757 - Cord/Cordless Shaver With LCD Display

World-wide A.C.voltage:100-240 Volts A.C.,50-60 Hz.

Charging

Charge your shaver 24 hours before initial use.

Make sure the ON/OFF button is set to OFF (with

“O” visible). Connect the cord to the shaver and then

to the electric outlet.

Model DA-307, DA-325,and DA-407 The Green indicator

light will glow indicating that the shaver is charging.

The shaver will be completely re c h a rged in 14-16 hours.

The red indicator light in the DA-325 model will glow

when the shaver needs to be re c h a rg e d .

Model DA-757 This shaver has an LCD display. The bars

on the display give the % of battery power left in your

shaver. The plug icon will flash when your shaver needs

to be recharged. There is also a foil replacement indica-

tor. The foil icon on the display will flash when the foil is

due for replacement. The one hour quick charge fea-

ture in this model gives up to 60 minutes of cordless

shaving time. A 5 minute quick charge gives enough

shaving time for one shave

To Shave

Model DA-57,and DA-107

Connect cord to shaver and then

to electric outlet.Slide the ON/OFF button upward to turn ON

.

CAUTION: THESE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR DISPOSED IN

A C C O R DANCE WITH STATE AND LOCAL REGULAT I O N S . Do not burn or mutilat e , as they

m ay burst or release toxic mat e r i a l s . Do not short-circuit, as it may cause burns.

Model DA-307 and DA-325 With the shaver unplugged,press in on the

Switch Lock and slide the ON/OFF button upward to turn ON.Note that this

shaver is designed only to operate from its batteries; it must be charged

before using.

Model DA-407,and DA-757 These shavers can be powered from either

the cord or the battery. To shave using the battery, make sure that the

shaver has been charged. To shave using the cord,connect cord to shaver

and then to electric outlet.Press in on the Switch Lock and slide the ON/OFF

button upward to turn ON.

Trouble Shooting

■

If your DA-407, 757 shaver bat t e ry is completely discharged or the shaver has

not been used for an extended period of time, the shaver may not start when oper-

ated using the cord. If this condition occurs,charge the shaver for ap p r o x i m at e ly

five minutes before shav i n g .

■

Your DA-407, 757 cord/cordless shaver should not be used strictly as a cord-

o p e r ated shav e r, as continued cord only use will result in reduction of bat t e ry life.

■

In order to preserve the life of the bat t e r i e s ,t h ey should be fully discharged every

six months and then fully charged for 24 hours.

Battery Removal

(Cord/Cordless and Cordless

Rechargeable Models Only)

When your rechargeable shav e r

reaches the end of its useful life, t h e

b atteries must be removed from the shaver and be recy cled

or disposed of properly in accordance with your local and stat e

r e q u i r e m e n t s .

The following procedure should be followed

for battery removal:

• To avoid a possible electrical shock hazard,unplug cord

from electrical outlet and shaver.

• Remove the head assembly by pushing in on the

head assembly release buttons.

• Remove the two screws on the upper back side of the

shaver.

• Pull or pry the shaver halves apart.

• Pull out the motor and frame assembl y.

• Pull or pry the batteries outward from the shaver’s

circuit board.

• Pull and twist the batteries to break the wire connections.

• CAUTION:Do not put in fire or mutilate your batteries when

disposing as they may burst or release toxic materials.Do

not short circuit as it may cause burns.Dispose of properly

in accordance with your local and state requirements.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Remington DA-57 Rakapparat. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Remington. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Remington DA-57 Rakapparat på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Remington Rakapparater
Fler bruksanvisningar för Rakapparater

Vanliga frågor om Remington DA-57 Rakapparat

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Remington XR1570 Ultimate Series Rakapparat

Bruksanvisning

Remington WSF5060 Rakapparat

Bruksanvisning

Remington WDF4815 Smooth & Silky Rakapparat

Bruksanvisning

Remington R9170 MicroFlex Ultra Rakapparat

Bruksanvisning

Remington WDF5030 Lady Rakapparat

Bruksanvisning

Remington TA5570 Rakapparat

Bruksanvisning

Remington HF9050 Heritage Rakapparat

Bruksanvisning

Remington PR1340 Power Rakapparat

Relaterade kategorier