Bruksanvisning Ozito AWG-964 Svetsmaskin

Bruksanvisning

• Under no circumstances should the housing of the welder be opened.

• Always protect your eyes and face with a welding mask.

• Wear appropriate protective clothing such as a welding apron and sleeved gloves

etc.

• Avoid exposing skin as UV rays are produced by the arc.

• Screen off the work place to protect others working nearby from UV rays.

• Welding materials with contaminated surfaces may generate toxic fumes. Ensure

the surface is clean before welding. Avoid operating on materials cleaned with

chlorinated solvents or near such solvents.

• Do not weld metal equipment that holds/contains ammable materials, gases or

liquid combustibles.

• Zinc-plated or galvanized material should not be welded as the fumes created are

highly toxic.

• Do not use the welder in damp or wet conditions.

• Do not use cables with worn insulation or loose connections.

• Disconnect from the power supply before replacing electrodes.

• Avoid direct contact with the welding circuit.

• Do not use the welder to defrost piping.

• Ensure the welder is placed on a level surface to prevent overturning.

• Provide adequate ventilation or a means for removal of the welding fumes

produced (forced circulation using a blower or fan).

Fumes

Toxic gases are given off during the ARC welding process, which may collect in the

welding area if the ventilation is poor. Be alert at all times to the possibility of fume

build-up. In small or conned areas use a fume extractor.

Glare

The electric arc generated by the arc process gives direct heat and ultraviolet

radiation. It is essential that the eyes of the operator and bystanders are protected

from the glare during welding.

ALWAYS USE A FACESHIELD OR WELDING HELMET FITTED WITH THE

CORRECT GLASS FILTER.

Heat

It is desirable that welding gloves are worn whilst welding. They will protect the

hands from ultra-violet radiation and direct heat of the arc.

Dress

In addition to face shield, welding gloves and overalls, other types of protective

clothing should be worn when welding. Additional protective clothing such as a

leather apron, sock protectors and a hat will all assist in reducing any injuries due to

heat, sparks and slag produced during welding.

OVERALLS should also be worn. They should be of type designed to be buttoned at

the wrists and the neck.

WELDER SAFETY WARNINGS

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of re, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before

operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

The electric motor has been designed for 230V and 240V only. Always check that the power supply

corresponds to the voltage on the rating plate.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid

a hazard.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not

suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric

shock.

It is recommended that the extension lead is a maximum of 25m in length. Do Not use multiple extension

leads.

The power supply for this product should be protected by a residual current device (rated at 30mA or less). A

residual current device reduces the risk of electric shock.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded) power tool or battery-operated (cordless)

power tool.

1. Keep work areas clean. Cluttered work areas and benches can cause accidents.

2. Consider work area environment. Do not expose your equipment to high humidity or rain. Do not use

your equipment in damp or wet conditions. Keep the work area well lit. Do not use your tool where there

is a risk of causing re or explosion, e.g. in the presence of ammable liquids and gases.

3. Keep children away. Do not allow children, visitors or animals to come near the work area or to touch

the equipment or accessories.

4. Dress appropriately. Wear the appropriate protective clothing. Wear a protective hair covering to keep

long hair out of the way.

5. Guard against electric shock. Prevent body contact with earthed or grounded surfaces. Electrical

safety can be further improved by using a high sensitivity (30 mA / 30 mS) residual current device (RCD).

6. Do not overreach. Keep proper footing and balance at all times.

7. Stay alert. Watch what you are doing. Use common sense. Do not operate the equipment when tired.

8. Secure work piece. If required, use clamps or a vice to hold the work piece.

9. Extension leads. Before use inspect the extension leads and replace if damaged. When using the

equipment outdoors, only use extension leads intended for outdoor use and marked accordingly.

10. Use appropriate equipment. Only use the equipment as outlined within this instruction manual. Do not

force the equipment to the job of heavier duty equipment. The equipment will do the job better and safer

at the rate for which it was intended. Do not force the equipment.

WARNING! The use of any accessory or attachment, or performance of any operation with this

equipment other than those recommended in this instruction manual may present a risk of personal

injury.

11. Check for damaged parts. Before use carefully check the equipment and power lead for damage.

Check for misalignment and seizure of moving parts, breakage of parts, damage to guards and switches

and any other conditions that may affect its operation. Ensure the equipment will operate properly and

perform its intended function. Do not use the equipment if any parts are damaged or defective. Do

not use the equipment if the switch does not turn it on and off. Have any damaged or defective parts

repaired or replaced by an electrician or a power tool repairer. Never attempt any repairs yourself

12. Unplug the equipment. Unplug the equipment when it is not in use, before changing any parts,

accessories or attachments and before servicing.

13. Do not abuse the cord. Never carry the equipment by its cord or pull it to disconnect from the socket.

Keep the cord away from heat, oil and sharp edges.

14. Store equipment. When not in use, equipment should be stored in a dry, locked up or high place,out of

reach of children.

15. Maintain mains equipment with care. Keep the equipment clean and in good condition for better and

safer performance. Follow the instructions for maintenance and changing accessories. Keep handles

and switches dry, clean and free from oil and grease.

16. Have your tool repaired by an electrician or a power tool repairer. This power tool complies with

relevant safety requirements. To avoid danger, electrical equipment must only be repaired by qualied

technicians using original spare parts; otherwise this may result in considerable danger to the user.

17. Users. This equipment is not intended for use by young children or inrmed persons without supervision.

Young children should be supervised to ensure that they do not play with this equipment.

18. Replacement of the supply cord. If the supply cord is damaged, it must be replaced by an electrician

or a power tool repairer in order to avoid a hazard.

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Ozito AWG-964 Svetsmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Ozito. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Ozito AWG-964 Svetsmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Ozito Svetsmaskiner
Fler bruksanvisningar för Svetsmaskiner

Vanliga frågor om Ozito AWG-964 Svetsmaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Ozito IWT-130 Svetsmaskin

Bruksanvisning

Ozito IWR-120 Svetsmaskin

Bruksanvisning

Ozito MWR-9045 Svetsmaskin

Bruksanvisning

Ozito MWR-090 Svetsmaskin

Bruksanvisning

Ozito MWR-135 Svetsmaskin

Bruksanvisning

Parkside IAN 494639 Svetsmaskin

Bruksanvisning

Stanley VIP M 165 Svetsmaskin

Bruksanvisning

Parkside PFDS 120 A1 Svetsmaskin

Relaterade kategorier