Bruksanvisning Orbis Circumat Rörelsedetektor

Bruksanvisning

CIRCUMAT

PROXIMITY SWITCH

INSTRUCTIONS ON USE

DESCRIPTION

The CIRCUMAT proximity switch captures the invisible infrared radiation from

persons and other heat sources, but without emitting any type of radiation itself.

When a heat source moves underneath the CIRCUMAT switch, its output circuit is

activated. Once movement is no longer captured, it will deactivate after an

adjustable delay time.

The proximity switch only reacts when the lighting conditions are below the

selected level.

INSTALLATION

WARNING: The assembly and installation of electrical apparatus must be carried

out by an authorised installer.

BEFORE PROCEEDING WITH THE INSTALLATION DISCONNECT THE POWER

SUPPLY.

The unit is internally protected against interference by means of a safety circuit.

However, certain extra strong electromagnetic fields could modify its operation

and, therefore, it must not be installed close to inductive fields (motors,

transformers, transformer substation or industrial machinery etc).

INSTALLATION AND CONNECTION

On the ceiling, avoiding highly reflective surfaces (liquids and marble etc) within its

detection area, elements that are subject to sharp changes in temperature

(heating, air conditioning and possible air currents etc) or light sources. The

detection area directly depends on the installation height, in accordance with the

following figure:

The installation of any proximity sensor must take into account that detection takes

place where the detection beams cross, so that if the heat source to be detected is

parallel to the beams, detection will occur at less distance because it does not

cross the beams until it is very close to the unit.

Remove the front cover by rotating it and pulling outwards. Release the two screws

in the front face to free the securing base. Fix the base to the ceiling with the two

screws (included) through the two drill holes. To facilitate the installation and

template is supplied for aligning the CIRCUMAT proximity switch with the walls.

It must be connected in accordance with the following diagram.

Refit the unit to the base with the two screws.

The environmental temperature in the location where the CIRCUMAT proximity

switch is installed has a significant influence on detection sensitivity, and therefore,

the detection distance. The higher the temperature, the worse the sensitivity

because the unit operates by detecting the movement of a heat source (in most

cases, this is 36 C, the temperature of the human body ), the closer the

temperature is to 36ºC, the poorer the detection.

PUTTING INTO SERVICE

The steps described below should be followed in order to adjust the detection field:

Rotate the “LUX” selector to the Q position and the “TIME” selector to the

minimum timer position . Check coverage by moving within the detection field

limits.

ADJUSTMENT

LUMINOSITY ADJUSTMENT: The CIRCUMAT proximity switch can be adjusted to

that it only operates when the lighting conditions are below the selected level. By

turning the “LUX” selector to the Q position, it will react under any luminosity

conditions. By turning it to the position, it will only react under low luminosity

conditions.

SWITCH-ON DELAY ADJUSTMENT: By turning the “TIME” selector to the Q

position, the switch-on delay will be approximately ten minutes. Turning it to the

position and the delay will be three seconds.

Replace the front cover, taking care to make the marks on each piece coincide.

For the changes made to take effect in the potentiometers in the adjustment

of the equipment, it is necessary to get out from the detection area and wait

for the installation to be turned off.

TECHNICAL SPECIFICATIONS

Power supply: 230 V~ 50 - 60 Hz

Switching power: 10 A / 250 V~

Maximum recommended loads:

Inca

ndescent lamps 2200 W

Fluorescent tubes 400 VA

Low voltage halogens (12V) 2000 VA

Halogens (230V) 2200 W

Low consumption lamps (CFL) 400 VA

Low consumption lamps (Downlights) 400 VA

LED lamps 400 VA

Own consumption: less than 2 W

Contact material: AgSn0

2

Sensitivity: 3 – 2000 Lux.

Timer range: from 3 seconds to 10 minutes

Detection angle: 360 º

Maximum detection height: 5 metres

Operating temperature: -20ºC to + 40ºC

Protection type: IP 20 according to EN 60529

Protection class: II under correct installation

conditions.

DIMENSIONS

01_2012 A016.13.53042

2.5 mts.

HIGHER SENSIBILITYLOWER SENSIBILITY

CENTRING INDEX

ORBIS TECNOLOGÍA ELÉCTRICA, S.A.

Lérida, 61 E–28020 MADRID

Teléfono:+ 34 91 5672277; Fax:+34 91 5714006

E-mail: info@ orbis.es

http://www.orbis.es

46

Ø138.5

26

N

L

N

L

N

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Orbis Circumat Rörelsedetektor. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Orbis. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Orbis Circumat Rörelsedetektor på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Orbis Rörelsedetektorer
Fler bruksanvisningar för Rörelsedetektorer

Relaterade produkter

Bruksanvisning

Orbis Proximat Rörelsedetektor

Bruksanvisning

Orbis Circumat Mini Rörelsedetektor

Bruksanvisning

Orbis Multimat Rörelsedetektor

Bruksanvisning

Orbis Isimat Rörelsedetektor

Bruksanvisning

Orbis Ecomat Rörelsedetektor

Bruksanvisning

Orbis Ecomat Mini Rörelsedetektor

Bruksanvisning

Orbis Isimat+ Rörelsedetektor

Bruksanvisning

Powerfix IAN 279891 Rörelsedetektor

Relaterade kategorier