Bruksanvisning Makita HR5000 Borrhammare

Bruksanvisning

Installing or removing drill bit or other bits

(bull point, etc.) (Fig. 3)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Insert the bit into the tool holder as far as it will go. Pull

out and turn the tool retainer 180 degrees. Then

release it to secure the bit.

CAUTION:

Never useA-typeshank bits. They can cause damage

to the tool.

To remove the bit, follow the installation procedure in

reverse.

Selecting action mode (Fig. 4)

Rotation with hammering:

For drilling in concrete, masonry, etc., rotate the

change lever to the

position.

Hammering only:

For chipping, scaling or demolition operations, rotate

the change lever to the

position.

CAUTION:

•

Do not rotate the change lever when the tool is

running under load. The tool will be damaged.

•

To avoid rapid wear on the mode change mecha-

nism, be sure that the change lever is always

positively located in one of the two action mode

positions.

Switch action (Fig. 5)

CAUTION:

•

Before plugging in the tool, always check to

see that the switch trigger actuates properly and

returns to the “OFF” position when released.

•

Do not tape, tie or otherwise secure the trigger in

the “ON” position.

To start the tool, simply pull the trigger. Release

the trigger to stop.

Hammer drilling operation

Position the bit at the location for the hole, then pull

the trigger.

Do not force the tool. Light pressure gives best

results. Keep the tool in position and prevent it

from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the

tool at an idle, then remove from the hole. By

repeating this several times, the hole will be cleaned

out.

CAUTION:

When the bit begins to break through concrete or if

the bit strikes reinforcing rods embedded in concrete,

the tool may react dangerously. Maintain good

balance and safe footing while holding the tool

firmly with both hands to prevent dangerous reaction.

Chipping / Scaling / Demolition

Hold the tool firmly with both hands. Turn the

tool on and apply slight pressure on the tool

so that the tool will not bounce around, uncon-

trolled. Pressing very hard on the tool will not

increase the efficiency.

Core bit (optional accessory)

When using the center bit

Screw the core bit on the adapter. Install the adapter

with the core bit in the tool in the same manner

as a drill bit. (Fig. 6)

Install the center bit. (Fig. 7)

Rest the core bit on the concrete and turn the

tool on. Once the core bit has cut a shallow

groove into the concrete, remove the center bit. Then

resume drilling.

To remove the core bit, follow the procedures (1)

or (2).

(1) Rotate the change lever to the

position. Then

rest the core bit on the concrete and turn the

tool on. The core bit will come loose from the

hammering action. (Fig. 8)

(2) Hold the adapter with the wrench, insert the rod

(optional accessory) into the hole in the core bit

and tap with a hammer to unscrew. (Fig. 9)

When not using the center bit

Screw the core bit on the adapter. Install the adapter

with the core bit in the tool in the same manner

as a drill bit. (Fig. 6)

Rotate the change lever to the

position. Rest the

core bit on the concrete and turn the tool on.

Once the core bit has cut a shallow groove into the

concrete, rotate the change lever to the

position

and resume drilling.

NOTE:

No problem is caused even if the core bit unscrews

slightly during brief use since the core bit rotates in

the tightening direction.

To remove the core bit, follow the same removal

procedures covered in When using the center bit.

6

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Makita HR5000 Borrhammare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Makita. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Makita HR5000 Borrhammare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Makita Borrhammare
Fler bruksanvisningar för Borrhammare

Vanliga frågor om Makita HR5000 Borrhammare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Makita DHR164 Borrhammare

Bruksanvisning

Makita HR2611FT Borrhammare

Bruksanvisning

Makita DHR242 Borrhammare

Bruksanvisning

Makita HR2430 Borrhammare

Bruksanvisning

Makita DHR165 Borrhammare

Bruksanvisning

Makita BHR262T Borrhammare

Bruksanvisning

Makita HR2010 Borrhammare

Bruksanvisning

Makita HR2810 Borrhammare

Relaterade kategorier