Bruksanvisning Makita BTL060 Mutterdragare

Bruksanvisning

7

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit. (Fig. 7)

For tool without sleeve to retain the bit

(Fig. 8)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

Use insert bits shown in the figure. To install the bit, just

insert it into the spindle. (Fig. 9)

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

Hook (Accessory)

CAUTION:

• When installing the hook, tighten the screw firmly.

Failure to do so may cause the breakage of the tool or

personal injury. (Fig. 10)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

Adjusting the angle head

The angle head can be adjusted 360° (8 positions in 45-

degree increments). To adjust it, loosen the hex bolt and

remove the angle head. Adjust the angle head to the

desired position and reinstall it so that the teeth on the

housing will match up with the grooves in the angle head.

Then tighten the hex bolt to secure the angle head.

(Fig. 11 & 12)

Straight head and ratchet head

(Accessory)

Straight heads and ratchet heads are available as

optional accessories for various applications on the job.

(Fig. 13 & 14)

OPERATION (Fig. 15 & 16)

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. Before starting your job,

always perform a test operation to determine the proper

fastening time for your screw. (Fig. 17)

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• Hold the tool pointed straight at the screw.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening torque

will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduction

in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Phillips bit

• Bit piece

• Straight head

• Ratchet head

• Socket

• Socket adapter

• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA

): 91 dB (A)

Sound power level (L

WA

): 102 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Makita BTL060 Mutterdragare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Makita. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Makita BTL060 Mutterdragare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Makita Mutterdragare
Fler bruksanvisningar för Mutterdragare

Vanliga frågor om Makita BTL060 Mutterdragare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Makita DTW181 Mutterdragare

Bruksanvisning

Makita DTD147 Mutterdragare

Bruksanvisning

Makita TD090D Mutterdragare

Bruksanvisning

Makita DTW284 Mutterdragare

Bruksanvisning

Makita DTS131 Mutterdragare

Bruksanvisning

Makita TD111D Mutterdragare

Bruksanvisning

Makita DTD137 Mutterdragare

Bruksanvisning

Makita DTL060 Mutterdragare

Relaterade kategorier