Bruksanvisning Makita 9563 Vinkelslip

Bruksanvisning

ENGLISH

Explanation of general view

1 Wheel cover

2 Screw

3 Lever

4 Bearing box

5 Press

6 Shaft lock

7 Lock nut

8 Depressed center wheel

9 Inner flange

0 Lock nut wrench

q Shaft lock

w Switch lever

e Exhaust vent

r Inhalation vent

SPECIFICATIONS

Model 9560 9561 9562

Depressed center wheel diameter ................................... 100 mm 115 mm 125 mm

Spindle thread .................................................................. M10 M14 M14

No load speed (min

-1

) ...................................................... 11,000 11,000 11,000

Overall length ................................................................... 289 mm 289 mm 289 mm

Net weight ........................................................................ 1.7 kg 1.7 kg 1.7 kg

Model 9563 9564 9565

Depressed center wheel diameter ................................... 100 mm 115 mm 125 mm

Spindle thread .................................................................. M10 M14 M14

No load speed (min

-1

) ...................................................... 11,000 11,000 11,000

Overall length ................................................................... 299 mm 289 mm 299 mm

Net weight ........................................................................ 1.8 kg 1.8 kg 1.8 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

ADDITIONAL SAFETY RULES ENB031-3

1. Always wear safety goggles and ear protec-

tors during operation.

2. Always be sure that the tool is switched off

and unplugged before carrying out any work

on the tool.

3. Keep guards in place.

4. Use only wheels with correct size and wheels

having a maximum operating speed at least as

high as the highest No Load Speed marked on

the tool’s nameplate.When using depressed

center wheels, be sure to use only fiberglass-

reinforced wheels.

5. Check the wheel carefully for cracks or dam-

age before operation. Replace cracked or

damaged wheel immediately.

6. Observe the instructions of the manufacturer

for correct mounting and use of wheels.

Handle and store wheels with care.

7. Do not use separate reducing bushings or

adaptors to adapt large hole abrasive wheels.

8. Use only flanges specified for this tool.

9. Do not damage the spindle, the flange (espe-

cially the installing surface) or the lock nut.

Damage to these parts could result in wheel

breakage.

10. For tools intended to be fitted with threaded

hole wheel, ensure that the thread in the wheel

is long enough to accept the spindle length.

11. Before using the tool on an actual workpiece,

test run the tool at the highest no load speed

for at least 30 seconds in a safe position. Stop

immediately if there is any vibration or wob-

bling that could indicate poor installation or a

poorly balanced wheel. Check the tool to

determine the cause.

12. Check that the workpiece is properly sup-

ported.

13. Hold the tool firmly.

14. Keep hands away from rotating parts.

15. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

16. Use the specified surface of the wheel to

perform the grinding.

17. Do not use cutting off wheel for side grinding.

18. Watch out for flying sparks. Hold the tool so

that sparks fly away from you and other per-

sons or flammable materials.

19. Pay attention that the wheel continues to

rotate after the tool is switched off.

20. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

21. Position the tool so that the power cord

always stays behind the tool during operation.

22. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a

short-circuit breaker (30 mA) to assure opera-

tor safety.

9560 (E) (’100. 12. 14)

5

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Makita 9563 Vinkelslip. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Makita. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Makita 9563 Vinkelslip på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Makita Vinkelslipar
Fler bruksanvisningar för Vinkelslipar

Vanliga frågor om Makita 9563 Vinkelslip

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Makita DGA506 Vinkelslip

Bruksanvisning

Makita GA4530R Vinkelslip

Bruksanvisning

Makita 9562CVH Vinkelslip

Bruksanvisning

Makita GA7020 Vinkelslip

Bruksanvisning

Makita DGA521 Vinkelslip

Bruksanvisning

Makita GA9050 Vinkelslip

Bruksanvisning

Makita GA4041C Vinkelslip

Bruksanvisning

Makita GA7050 Vinkelslip

Relaterade kategorier