Bruksanvisning Makita 9049F Vinkelslip

Bruksanvisning

ENGLISH

Explanation of general view

1 Wheel guard

2 Screw

3 Notch

4 Side grip

5 Lock nut

6 Depressed center wheel

7 Inner flange

8 Super flange

9 Lock nut wrench

0 Shaft lock

q Switch trigger

w Lock lever

e Brush holder cap

r Screwdriver

SPECIFICATIONS

Model 9047/9047S 9057/9057S 9049/9049S 9059/9059S

9047F/9047SF 9057F/9057SF 9049F/9049SF 9059F/9059SF

Depressed center wheel diameter ........................ 180 mm 180 mm 230 mm 230 mm

No load speed (RPM) ........................................... 8,500 8,500 6,600 6,600

Overall length ........................................................ 470 mm 470 mm 470 mm 470 mm

Net weight ............................................................. 4.8 kg 5.1 kg 4.8 kg 5.1 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

For models 9047, 9049, 9057 and 9059, public

low-voltage distribution systems of between

220 V and 250 V

Switching operations of electric apparatus cause volt-

age fluctuations. The operation of this device under

unfavorable mains conditions can have adverse

effects to the operation of other equipment. With a

mains impedance equal or less than 0.22 (for 9047

and 9049) / 0.24 (for 9057 and 9059) Ohms it can be

presumed that there will be no negative effects.

The mains socket used for this device must be

protected with a fuse or protective circuit breaker

having slow tripping characteristics.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Always be sure that the tool is switched off

and unplugged before carrying out any work

on the tool.

2. Keep guards in place.

3. Use only wheels having a maximum operating

speed at least as high as ‘‘No Load RPM’’

marked on the tool’s nameplate.

When using depressed center wheels, be sure

to use only fiberglass-reinforced wheels.

4. Check the wheel carefully for cracks or dam-

age before operation. Replace cracked or

damaged wheel immediately.

5. Use only flanges specified for this tool.

6. Do not damage the spindle, the flange (espe-

cially the installing surface) or the lock nut.

Damage to these parts could result in wheel

breakage.

7. Keep hands away from rotating parts.

8. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

9. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced wheel.

10. Use the specified surface of the wheel to

perform the grinding.

11. Watch out for flying sparks. Hold the tool so

that sparks fly away from you and other per-

sons or flammable materials.

12. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

13. Always wear safety goggles and ear protec-

tors during operation.

14. Position the tool so that the power cord

always stays behind the tool during operation.

15. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a

short-circuit breaker (30 mA) to assure opera-

tor safety.

16. Do not use the tool on any materials contain-

ing asbestos.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing wheel guard (Fig. 1)

When installing a depressed center wheel or an

abrasive cut-off wheel, always use a wheel guard.

Mount the wheel guard with the tab on the wheel

guard band aligned with the notch on the bearing box.

Then rotate the wheel guard 160 degrees counter-

clockwise. Be sure to tighten the screw securely.

4

9047(E) (’100. 10. 11)

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Makita 9049F Vinkelslip. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Makita. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Makita 9049F Vinkelslip på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Makita Vinkelslipar
Fler bruksanvisningar för Vinkelslipar

Vanliga frågor om Makita 9049F Vinkelslip

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Makita GA9061 Vinkelslip

Bruksanvisning

Makita GA7020 Vinkelslip

Bruksanvisning

Makita GA9030S Vinkelslip

Bruksanvisning

Makita GA7030S Vinkelslip

Bruksanvisning

Makita GA4540C Vinkelslip

Bruksanvisning

Makita DGA402 Vinkelslip

Bruksanvisning

Makita GA6040C Vinkelslip

Bruksanvisning

Makita 9555NB Vinkelslip

Relaterade kategorier