Bruksanvisning Makita 6411 Borrskruvdragare

Bruksanvisning

3

ENGLISH

Explanation of general view

1 Chuck key

2 Ring

3Sleeve

4 Switch trigger

5 Lock button

6 Reversing switch lever

SPECIFICATIONS

Model 6411 6412 6413

Capacities

Steel .........................................................................................10 mm 10 mm 10 mm

Wood ........................................................................................25 mm 25 mm 25 mm

No load speed (min

–1

) .................................................................3,000 0 – 3,000 0 – 3,000

Overall length ..............................................................................228 mm 228 mm 234 mm

Net weight ....................................................................................1.3 kg 1.3 kg 1.3 kg

Safety class .................................................................................. /II /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use

The tool is intended for drilling in wood, metal and plastic.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

GEB001-6

DRILL SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold power tools by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

8. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

OPERATING INSTRUCTIONS

Installing or removing drill bit

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

For 6411, 6412 (Fig. 1)

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each

of the three holes and tighten clockwise. Be sure to

tighten all three chuck holes evenly.

To remove the bit, turn the chuck key counterclockwise in

just one hole, then loosen the chuck by hand.

For 6413 (Fig. 2)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as

it will go. Hold the ring firmly and turn the sleeve clock-

wise to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve coun-

terclockwise.

Switch action (Fig. 3)

CAUTION:

• Before plugging in the tool, always check to see the

switch trigger actuates properly and returns to the

“OFF” position when released.

For 6411

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

For 6412, 6413

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Makita 6411 Borrskruvdragare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Makita. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Makita 6411 Borrskruvdragare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Makita Borrskruvdragare
Fler bruksanvisningar för Borrskruvdragare

Vanliga frågor om Makita 6411 Borrskruvdragare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Makita DP2011 Borrskruvdragare

Bruksanvisning

Makita DDF453 Borrskruvdragare

Bruksanvisning

Makita DHP490 Borrskruvdragare

Bruksanvisning

Makita DHP343 Borrskruvdragare

Bruksanvisning

Makita DS4012 Borrskruvdragare

Bruksanvisning

Makita DA3010F Borrskruvdragare

Bruksanvisning

Makita M6000 Borrskruvdragare

Bruksanvisning

Makita DHP444 Borrskruvdragare

Relaterade kategorier