Bruksanvisning Hozelock 3352 Cascade 700 Fontänpump

Bruksanvisning

The Hozelock Cyprio Cascade 700 pump is

designed for submersible use only. The pump

does not use oil or grease for lubrication

and can be used safely in ponds containing

fish or plants. The motor consists of a sealed

stator and water-cooled permanent magnet

rotor. All electrical components are isolated

from the water.

IMPORTANT

1. WARNING: ALWAYS UNPLUG OR

DISCONNECT ALL APPLIANCES IN THE

POND FROM THE ELECTRICITY SUPPLY

BEFORE PUTTING YOUR HANDS IN THE

WATER WHILST EQUIPMENT IS BEING

INSTALLED, REPAIRED, MAINTAINED OR

HANDLED.

2. Do not use the supply cable to lift the

pump, as this may cause damage. We

recommend fitting a lifting cord to the

handle eye on the top of the strainer cage

when the pump is installed in deep water.

See fig 1.

3. Do not operate or leave the pump in

freezing conditions.

4. Do not allow the pump to run dry.

5. Check that the voltage marked on the

pump corresponds to the mains supply.

6. A 10MA OR 30 MA RESIDUAL CURRENT

DEVICE MUST

BE FITTED TO THE MAINS

SUPPLY.

7. DO NOT OPERATE THIS PUMP WITHOUT

THE STRAINER CAGE ATTACHED. USING

THE PUMP WITHOUT A STRAINER MAY

INVALIDATE YOUR WARRANTY.

Safety Information

The appliance is not intended for use by

persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use

of the appliance by a person responsible

for their safety. Children should be

supervised to ensure that they do not

play with the appliance.

WARNING: SAFETY AND

ELECTRICAL CONNECTIONS

1. The pump is supplied with 10m of 3 core

electric cable which is permanently

connected and sealed to the motor.

The supply cable cannot be replaced. If

the cable is damaged, the pump should

be discarded.

WARNING: THE PLUG SUPPLIED WITH THIS

PRODUCT IS NOT WATERPROOF AND THE

CONNECTION TO THE MAINS SUPPLY

SHOULD ONLY BE MADE IN A

WEATHERPROOF ENCLOSURE.

The installation must conform to the

regulations of the local electricity

authority which could include the use of

plastic or metal conduit to protect the

cable.

2. A 10MA OR 30MA RESIDUAL CURRENT

DEVICE (RCD) MUST

BE FITTED TO THE

MAINS SUPPLY.

3. WARNING: THIS APPLIANCE MUST

BE

EARTHED AND IT IS ESSENTIAL THAT THE

CONNECTIONS ARE MADE USING THE

FOLLOWING CODE;

Brown - Live

Blue - Neutral

Green/Yellow - Earth

The BROWN lead should be connected to

the LIVE terminal which may be marked

with an ‘L’ or coloured brown or red.

The BLUE lead should be connected to the

NEUTRAL terminal which may be marked

with an ‘N’ or coloured blue or black.

The GREEN/YELLOW lead should be

connected to the EARTH terminal which

may be marked with an ‘E’ or coloured

green or green/yellow.

4. If an extension cable is required, this

should be connected to the end of the

pump cable using a weatherproof cable

connector. The joint must be positioned in

a suitable weatherproof housing. The

extension cable should be of 3 core

0.75mm

2

Polychloroprene rubber

insulated cable (ref: HO5 RN-F) and

permanently wired to the mains supply

with a 3 or 5 Amp fuse.

5. The pump cable (and extension cable)

should be positioned and adequately

protected against damage especially

where contact with gardening equipment

(lawn mowers, forks etc..) children and

domestic animals may occur.

6. CONSULT A QUALIFIED ELECTRICIAN OR

LOCAL AUTHORITY IF IN ANY DOUBT

ABOUT WIRING TO THE MAINS SUPPLY.

ACCESSORY ASSEMBLY

Telescopic Stem Assembly.

Take the outer telescopic stem ‘A’ and slide

the inner stem ‘B’ into it, as shown. See Fig 2.

Bell Fountain

1. Locate the Bell Support (D) to the Bell

Main Body (E) and push fully home.

2. Position the Bell (F) to the Body Assembly

and press into the central location.

See fig 3.

PUMP INSTALLATION

Position

Construct a solid and level platform on which

to place the pump. When using spray

fountains, the top of the platform should be

240-330mm (10-13”) below the water

surface.

When using the bell fountain, the top of the

platform should be 100mm (4”) below the

water level.

A typical installation is shown for guidance

in Fig 4.

Flow Control

The flow from the pump can be regulated to

meet your needs by rotating the flow

controller wheel (G) near the outlet of the

pump. See Fig 5.

Fountain Only

1. Place the pump next to the pond and

route the cable back to the mains supply.

2. Select the desired fountain accessory. The

2 and 3 tier fountainheads simply snap

onto the fountain stem (See Fig 6). The

fountain stem pushes onto the narrower

tube section of the telescopic fountain

stem (See Fig 6). Then place the pump in

the desired position. Note: Check that the

inner stem of the telescopic tube has not

been pushed inside the outer tube.

3. a). 3 tier fountain – Creates a wider and

attractive fountain spray.

b). 2 tier fountain – Creates a higher and

narrower display.

c). Bell fountain – Creates a decorative

water bell. Adjust the telescopic stem to

the required height and regulate the bell

by rotating the flow controller by the

outlet of pump.and by sliding the inner

bell in and out of the bell assembly.

4. The ball joint - See Fig 5 (H), fits onto the

pump outlet and the telescopic stem

pushes onto the top. This can then be

used to adjust the fountain angle so that

it is vertical.

Waterfall Only

1. Fit a suitable length of hose 12.5mm bore

hose on to the hose adaptor. See Fig 5 (I).

2. Route the hose back to the waterfall.

MAINTENANCE

The Hozelock Cyprio range of Cascade

pumps has been designed to allow fast and

easy maintenance. As with all pumps of its

kind, occasionally it will become necessary to

clean the Strainer Cage and Fountain Spray

head ring.

ALWAYS UNPLUG OR DISCONNECT ALL

APPLIANCES IN THE POND FROM THE

ELECTRICITY SUPPLY BEFORE PUTTING YOUR

HANDS IN THE WATER OR STARTING

MAINTENANCE.

Fountain Head

1. Place a coin or similar in the slot and

gently lever off the fountain head.

2. Rinse in clean water and reassemble.

Strainer.

1. Remove the accessories from the pump

outlet.

2. Holding the pump in one hand, press the

release button (J) on the top of the pump

and open Strainer Cage. See Fig 5.

3. Slide the pump out of its location and

wash/rinse the Strainer Cage with clean

water. The hinges on the Strainer Cage

should also be washed clean at this time.

4. Reassemble the pump.

Rotor Assembly

1. Remove the Strainer Cage as described

above.

2. Release the Pump Chamber, Fig 7 (K), by

rotating it until the two retaining tongues

are clear of the lugs on the Motor Body.

3. Gently pull the Pump Chamber squarely

away from the Motor Body.

4. Pull the Rotor Assembly out of the Motor

Body. See Fig 7 (L).

5. Wash out all of the components in clean

water. Do not use detergents or other

chemical cleaners.

6. Replace the Rotor Assembly into the

Motor Body and refit the Pump Chamber

and Strainer Cage.

ALL YEAR PUMP CARE

A quick daily check should be carried out to

ensure that the pump is performing

satisfactorily.

Once a week- Remove and clean the Strainer

Cage and Fountain Head in accordance with

the general maintenance notes. Depending

on pond water conditions, cleaning may be

required more frequently.

Once a year- Completely disassemble the

pump including the Rotor Assembly as

described in the general maintenance notes

and wash all components in clean, fresh

water. Replace worn or broken parts.

SPARE PARTS

Contact the Consumer Services Helpline on

0121 313 1122

HOZELOCK CYPRIO 3 YEAR

GUARANTEE

If this pump, excluding the Rotor Assembly,

becomes unserviceable within 3 years of the

date of purchase it will be repaired or

replaced at our option free of charge, unless

in our opinion it has been damaged or

misused.

Liability is not accepted for damage due to

accident, improper installation or use.

Liability is limited to replacement of a faulty

pump. This guarantee is not transferable. It

does not affect your statutory rights.

To obtain the benefits of the guarantee,

firstly contact Hozelock Cyprio Consumer

Services who may request that the pump is

sent along with proof of purchase directly to

the address below.

2

GB

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Hozelock 3352 Cascade 700 Fontänpump. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Hozelock. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Hozelock 3352 Cascade 700 Fontänpump på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Hozelock Fontänpumpar
Fler bruksanvisningar för Fontänpumpar

Relaterade produkter

Bruksanvisning

Hozelock 3303 Cascade 450 Fontänpump

Bruksanvisning

Hozelock 1586A Aquaforce 15000 Fontänpump

Bruksanvisning

Hozelock 1764 EasyClear 6000 Fontänpump

Bruksanvisning

Hozelock 1760 EasyClear 3000 Fontänpump

Bruksanvisning

Hozelock 1581 Aquaforce 2500 Fontänpump

Bruksanvisning

Hozelock 1766 EasyClear 7500 Fontänpump

Bruksanvisning

Hozelock 1583A Aquaforce 6000 Fontänpump

Bruksanvisning

Hozelock 1762 EasyClear 4500 Fontänpump

Relaterade kategorier