Bruksanvisning Hozelock 3334 Cascade 3000 Fontänpump

Bruksanvisning

2

The Hozelock Cyprio Cascade 3000 / 4000

pump is designed for submersible use only.

The pump does not use oil or grease for

lubrication and can be used safely in ponds

containing fish or plants. The motor consists

of a sealed stator and water-cooled

permanent magnet rotor. All electrical

components are isolated from the water.

IMPORTANT

1. WARNING: ALWAYS UNPLUG OR

DISCONNECT ALL APPLIANCES IN THE

POND FROM THE ELECTRICITY SUPPLY

BEFORE PUTTING YOUR HANDS IN THE

WATER WHILST EQUIPMENT IS BEING

INSTALLED, REPAIRED, MAINTAINED OR

HANDLED.

2. Do not use the supply cable to lift the

pump, as this may cause damage. We

recommend fitting a lifting cord to the

handle eye on the top of the strainer cage

when the pump is installed in deep water.

3. Do not operate or leave the pump in

freezing conditions.

4. Do not allow the pump to run dry.

5. Check that the voltage marked on the

pump corresponds to the mains supply.

6. A 10MA OR 30MA RESIDUAL CURRENT

DEVICE MUST

BE FITTED TO THE MAINS

SUPPLY.

7. DO NOT OPERATE THIS PUMP

WITHOUT THE STRAINER CAGE

ATTACHED. USING THE PUMP WITHOUT A

STRAINER CAGE MAY INVALIDATE YOUR

WARRANTY.

Safety Information

The appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for

their safety. Children should be

supervised to ensure that they do not

play with the appliance.

WARNING: SAFETY AND

ELECTRICAL CONNECTIONS

1. The pump is supplied with 10m of 3 core

electric cable which is permanently

connected and sealed to the motor.

The supply cable cannot be replaced. If

the cable is damaged, the pump should be

discarded.

WARNING: THE PLUG SUPPLIED WITH THIS

PRODUCT IS NOT WATERPROOF AND THE

CONNECTION TO THE MAINS SUPPLY

SHOULD ONLY BE MADE IN A

WEATHERPROOF ENCLOSURE.

The installation must conform to the

national and local wiring regulations

which could include the use of plastic or

metal conduit to protect the cable.

2. A 10MA OR 30MA RESIDUAL CURRENT

DEVICE (RCD) MUST

BE FITTED TO THE

MAINS SUPPLY.

3. WARNING: THIS APPLIANCE MUST

BE

EARTHED AND IT IS ESSENTIAL THAT THE

CONNECTIONS ARE MADE USING THE

FOLLOWING CODE;

Brown - Live

Blue - Neutral

Green/Yellow - Earth

The BROWN lead should be connected to

the LIVE terminal which may be marked

with an ‘L’ or coloured brown or red.

The BLUE lead should be connected to the

NEUTRAL terminal which may be marked

with an ‘N’ or coloured blue or black.

The GREEN/YELLOW lead should be

connected to the EARTH terminal which

may be marked with an ‘E’ or coloured

green or green/yellow.

4. If an extension cable is required, this

should be connected to the end of the

pump cable using a weatherproof cable

connector. The joint must be positioned in

a suitable weatherproof housing. The

extension cable should be of 3 core

0.75mm

2

Polychloroprene rubber insulated

cable (ref: HO5 RN-F) and permanently

wired to the mains supply with a 3 or 5

Amp fuse.

5. The pump cable (and extension cable)

should be positioned and adequately

protected against damage especially

where contact with gardening equipment

(lawn mowers, forks etc.) children and

domestic animals may occur.

6. CONSULT A QUALIFIED ELECTRICIAN OR

LOCAL AUTHORITY IF IN ANY DOUBT

ABOUT WIRING TO THE MAINS SUPPLY.

ACCESSORY ASSEMBLY

Tee Piece

1. Locate the fountain flow adjuster (See

Fig1-A) to the tee piece body with the peg

positioned downwards to engage in the

tee. Push in fully and snap them together.

2. Locate the valve stem (B) to the waterfall

flow adjuster (C) and snap them together.

Screw the valve assembly into the longer

boss (D) on the tee piece. See fig 1.

Telescopic Stem

1. Slide the Inner Tube (E) through the

Telescopic Stem Nut (F) and “O” ring (G).

Push the Inner Tube into the Outer Tube

(H) and gently screw down the nut. The

finishing position of the tee piece is not

important. The maximum to minimum

range of the Telescopic stem is 150mm (6”)

(See fig 2).

Bell Fountain

1. Locate the Bell Support (I) to the Bell Main

Body (J) and push fully home.

2. Position the Bell (K) to the Body Assembly

and press into the central location.

See fig 3.

PUMP INSTALLATION

ATTENTION: This product is not

suitable for water temperatures

above 35ºC

Position

Construct a solid and level platform on which

to place the pump. For installations using the

fountain tops directly on the Tee Piece, the

top level of the platform should be 300 mm

(12”) below the water level. For installations

using the fountain tops directly on the Tee

Piece and Telescopic Stem , the top level of

the platform should be 450 mm (18”) below

the water level.

Fountain Only. (See Fig 7 for general

installation guide)

1. Place the pump next to the pond and

route the cable back to the mains supply.

2. Position the pump with the Tee Piece

Assembly and if required the Telescopic

Stem with the fountain fitted in the

desired position in the pond. The 2 and 3

tier fountain heads simply snap onto the

fountain stem (See Fig 4).

3. The fountain height can be regulated to

suit your needs by rotating the Fountain

Flow Adjuster. See Fig 5 (L).

4. If required, the 2-Tier Fountain head, Fig 5

(M), can be used to achieve an alternative

and higher display pattern than the 3-Tier,

Fig 5 (N).

5. The Bell Fountain creates a decorative

waterbell. The size of the bell can be

regulated by adjusting the flow through

the Tee Piece by rotating the fountain

flow adjuster and or by raising or

lowering the top of the Bell in main Bell

Body.

6. The ball joint on the bottom of the tee

Piece (See Fig 5, O) can be used to adjust

the fountain angle so that it is vertical.

Fountain and Waterfall. (See Fig 8 for general

installation guide)

1. Position the pump as previously described.

2. Attach a suitable length of 25 mm (1”)

hose to the Threaded Hose tail, Fig 5 (P),

and secure with a suitable hose clip and

position the outlet end of the hose in the

desired position.

3. Screw the Threaded Hose tail onto the

waterfall outlet side of the Tee Piece.

4. The combination of waterfall and

fountain will reduce the fountain height

that can be achieved.

5. Once the pump is operating the flow of

the waterfall and the height of the

fountain can be independently adjusted.

Waterfall Only. (See Fig 9 for general

installation guide)

1. Position the pump as previously described.

2. Attach a suitable length of 25 mm (1”)

hose to the Threaded Hose tail and secure

with a suitable hose clip and position the

outlet end of the hose in the desired

position.

3. For maximum waterfall flow, screw the

Threaded Hose tail directly onto the outlet

of the pump. Some installations require

the flow of the water to be adjusted. In

these cases, screw the Tee Piece to the

outlet of the pump, screw the Threaded

Hose tail to the water fall outlet boss and

adjust the flow using the waterfall flow

adjuster, Fig 5 (Q), to suit your needs.

MAINTENANCE

The Hozelock Cyprio range of Cascade pumps

has been designed to allow fast and easy

maintenance. As with all pumps of its kind,

occasionally it will become necessary to clean

the Strainer Cage and Fountain Spray head

ring.

ALWAYS UNPLUG OR DISCONNECT ALL

APPLIANCES IN THE POND FROM THE

ELECTRICITY SUPPLY BEFORE PUTTING YOUR

HANDS IN THE WATER OR STARTING

MAINTENANCE.

Fountain Head

1. Place a coin or similar in the slot and

gently lever off the fountain head.

2. Rinse in clean water and reassemble.

Strainer

1. Remove the accessories from the pump

outlet.

2. Holding the pump in one hand, press the

release button on the top of the pump

and open Strainer Cage. See Fig 5 (R).

3. Slide the pump out of its location and

wash/rinse the Strainer Cage with clean

water. The hinges on the Strainer Cage

should also be washed clean at this time.

4. Reassemble the pump.

Rotor Assembly

1. Remove the Strainer Cage as described

above.

2. Release the Pump Chamber, Fig 6 (S), by

rotating it until the two retaining tongues

are clear of the lugs on the Motor Body.

3. Gently pull the Pump Chamber squarely

GB

ATTENTION

AUTOMATIC CUT-OUT. To help ensure

your pump’s long life and to prevent

damage, it is fitted with automatic

thermal overload protection. This

switches off the pump if it overheats. If

this occurs, switch off the power at the

mains supply to the pump. Check for the

cause. Usually it will be debris blocking

the inlets of the pump or obstructing the

impeller. Remove the obstruction and

wait 15 minutes for the pump to cool

down and automatically reset. Then

switch on the pump again.

NOTE: YOU MUST SWITCH OFF THE MAINS

SUPPLY BEFORE THE PUMP WILL RESET.

33634-004 CASC.3000/4000 INTL.qxp_33446 CASC.1500 INTL 19/01/2016 18:52 Page 2

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Hozelock 3334 Cascade 3000 Fontänpump. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Hozelock. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Hozelock 3334 Cascade 3000 Fontänpump på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Hozelock Fontänpumpar
Fler bruksanvisningar för Fontänpumpar

Relaterade produkter

Bruksanvisning

Hozelock 1584A Aquaforce 8000 Fontänpump

Bruksanvisning

Hozelock 1585A Aquaforce 12000 Fontänpump

Bruksanvisning

Hozelock 1762 EasyClear 4500 Fontänpump

Bruksanvisning

Hozelock 1768 EasyClear 9000 Fontänpump

Bruksanvisning

Hozelock 1583A Aquaforce 6000 Fontänpump

Bruksanvisning

Hozelock 3344 Cascade 4000 Fontänpump

Bruksanvisning

Hozelock 1766 EasyClear 7500 Fontänpump

Bruksanvisning

Hozelock 1581 Aquaforce 2500 Fontänpump

Relaterade kategorier