Bruksanvisning Hoover HDI 90 X Köksfläkt

Bruksanvisning

ENGLISH

DESCRIPTION

The hood may be installed in the filtering or the ducting version.

In the Filtering version the air and the kitchen fumes that are conveyed by the apparatus are depurated by

the charcoal filter and put back into the room through the small grilles of the ventilation flue (Fig. 1).

ATTENTION: When using the filtering version, a charcoal filter and an air baffle (Fig. 1A) must be used, which

placed at the top of the structure, allows the air to recycle back into the room.

In the Ducting version, cooking vapours and odours are conveyed straight outside by a disposal duct which

passes through the ceiling (Fig. 2).

INSTALLATION

ATTENTION: Three people are required for proper installation; the unit should be installed by a qualified

operator. Also follow carefully each step of the assembly instructions, and once installation has been

completed, make sure that the hood is firmly secured in place.

To facilitate installation, before starting remove the grease filters: press inward on the clamp at the handle and

pull the filter downward (Fig. 3).

For assembling it is essential to: – Prepare the electrical connection and the air exhaust pipe (CAUTION! For installation

reasons the pipe must absolutely be flexible) inside the telescopic flue so that they are sufficiently long to reach the lower

flue outlet (Fig. 4). – If your unit is installed in a ducting hood, prepare the air exhaust hole.

When installing ducting hoods, to achieve the best possible conditions use an air exhaust pipe that : is as short

as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which

vary from nation to nation) and is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section

(diameter: 150 mm).

ASSEMBLING - Using the special drilling template, drill the holes for fixing to the ceiling on the vertical side of

your hob. Carefully observe all the indications for final positioning of the apparatus. Take into account that one of

the template axes must correspond to the axis of the hood controls. Fix the bracket to the ceiling using the screws

and screw anchors provided (Fig. 5). Be careful, because the position of the bracket determines the final position

of the apparatus.

Ducting version: Fix the upper flue to the bracket by means of the four screws provided (Fig. 6), with the grilles facing

down, then take the lower flue and insert it in the upper one (Fig. 7). Adjust the height of the flues with the eight retaining

screws (Fig. 7A) taking into account that the distance between the hood and the hob must be at least 650 mm (Fig. 8).

Take the flange with the metal valve (Fig. 9H) and assemble it onto the opening of the hood for air venting, pressing slightly.

Now make the electrical connection A and connect the air exhaust pipe to the flange B holding the hood raised (Fig.10).

Lift the island and rest it against the lower flue, then fix the parts with the eight screws provided (Fig. 11). At this point

the installation is complete and the grease filters can be remounted.

Filtering version: After fitting the bracket to the ceiling, install the baffle (Fig. 12) with the four screws “A”; fix the flange

“B” with a rotating movement. Arrange the power cable and the air exhaust pipe as shown in Figure 13. Repeat the

installation from the first point of the ducting version bearing in mind that the upper flue must have the grilles facing up.

OPERATION

Commands (Fig. 14): Button A: light switch. Button B: first speed motor ON/OFF switch. Button C: second

speed switch. Button D: third speed switch. E: motor on light.

Pay special attention to the grease filters; the grease filter must be cleaned periodically: exactly how often

depends on use (at least once every other month). To remove the filters: press inward on the clamps at the handles

and pull the filter downward (Fig. 3). Wash out the filter using a neutral soap.

Replacing the charcoal filter: If the unit is a filtering hood, the charcoal filters must be replaced: to remove

them press inward on the clamp (Fig. 15) and rotate the filter downward until the 2 tabs can be removed from

the housing. The charcoal filter must be replaced according to use: on average once every 6 months.

Lighting: Depending on the model purchased, see Fig.16 or Fig. 17.

Fig. 16: to remove the halogen lamps, turn the locknut counter-clockwise. Replace with the same type of lamp.

Fig. 17: to change the halogen lamps open the cover levering from the proper slots. Replace with the same type of lamp.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Hoover HDI 90 X Köksfläkt. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Hoover. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Hoover HDI 90 X Köksfläkt på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Hoover Köksfläktar
Fler bruksanvisningar för Köksfläktar

Vanliga frågor om Hoover HDI 90 X Köksfläkt

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Hoover HTS6CBK5XWIFI Köksfläkt

Bruksanvisning

Hoover HCV61/2C Köksfläkt

Bruksanvisning

Hoover HECH616/3X AUS Köksfläkt

Bruksanvisning

Hoover HGM61X Köksfläkt

Bruksanvisning

Hoover HHT6300/1X Köksfläkt

Bruksanvisning

Hoover HDTI6500/1X Köksfläkt

Bruksanvisning

Hoover HDSV985B AUS Köksfläkt

Bruksanvisning

Hoover HCV61/2WA Köksfläkt

Relaterade kategorier