Bruksanvisning Hikoki DV 22V Slagborrmaskin

Bruksanvisning

4

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

(1) Chuck wrench (Spec. only for keyed chuck) ................1

(2) Side handle ..................................................................1

(3) Depth gauge ................................................................1

(4) Plastic case ..................................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

○ By combined actions of ROTATION and IMPACT:

Boring holes in hard materials (concrete, marble, granite,

tiles, etc.)

○ By ROTATIONAL action:

Boring holes in metal, wood and plastic.

SPECIFICATIONS

Voltage*

1

(110 V, 220 V, 230 V, 240 V)

Power input 1120 W*

1

Speed range 1 2

No load speed 0 – 1100 min

-1

0 – 3000 min

-1

Capacity

Steel

16 mm 8 mm

Concrete

22 mm 13 mm

Wood

40 mm 25 mm

Full-load impact rate

8100 min

-1

22000 min

-1

Weight*

2

3.0 kg

*1 Be sure to check the nameplate on product as it is subject

to change by areas.

*2 Weight: According to EPTA-Procedure 01/2003

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Insulated gripping surface 1 99

Fixing and removing side handle

299

Using depth stopper 3 99

Mounting and dismounting of

the bit

499

Selecting rotation direction 5 100

Selecting the operating mode 6 100

Switch operation

7 100

Locking-on the switch

8 100

Releasing the switch

9 100

Change rotation speed

10 101

Selecting accessories ― 102

Selecting the appropriate drill bit

○ When boring concrete or stone

Use the drill bits specifi ed in the Optional Accessories.

○ When boring metal or plastic

Use an ordinary metalworking drill bit.

○ When boring wood

Use ordinary woodworking drill bit.

However, when drilling 6.5 mm or smaller holes, use a

metalworking drill bit.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of an abraded drill bits will cause motor

malfunctioning and degraded effi ciency, replace the drill

bits with a new one or resharpening without delay when

abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI Authorized

Service Center.

5. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

0000Book̲DV22V.indb40000Book̲DV22V.indb4 2017/12/0411:31:242017/12/0411:31:24

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Hikoki DV 22V Slagborrmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Hikoki. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Hikoki DV 22V Slagborrmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Hikoki Slagborrmaskiner
Fler bruksanvisningar för Slagborrmaskiner

Vanliga frågor om Hikoki DV 22V Slagborrmaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Hikoki VTP-16A Slagborrmaskin

Bruksanvisning

Hikoki D 13VB3 Slagborrmaskin

Bruksanvisning

Hikoki DV 13VSS Slagborrmaskin

Bruksanvisning

Hikoki D 13VL Slagborrmaskin

Bruksanvisning

Hikoki DV 20VD Slagborrmaskin

Bruksanvisning

Hikoki DV 13SS Slagborrmaskin

Bruksanvisning

Hikoki DV 16V Slagborrmaskin

Bruksanvisning

Hikoki DV 20VB2 Slagborrmaskin

Relaterade kategorier