Bruksanvisning Hikoki C 6U3 Cirkelsåg

Bruksanvisning

4

English

Riving knife function

a) Use the appropriate saw blade for the riving knife.

For the riving knife to function, the body of the blade

must be thinner than the riving knife and the cutting

width of the blade must be wider than the thickness of

the riving knife.

b) Adjust the riving knife as described in this

instruction manual.

Incorrect spacing, positioning and alignment can make

the riving knife ineff ective in preventing kickback.

c) Always use the riving knife except when plunge

cutting.

The riving knife must be replaced after plunge cutting.

The riving knife causes interference during plunge

cutting and can create kickback.

d) For the riving knife to work, it must be engaged in

the workpiece.

The riving knife is ineff ective in preventing kickback

during short cuts.

e) Do not operate the saw if the riving knife is bent.

Even a light interference can slow the closing rate of a

guard.

ADDITIONAL SAFETY WARNINGS

1. Use only blade diameter specifi ed on the machine.

2. Do not use any abrasive wheel.

3. Do not use saw blades which are deformed or cracked.

4. Do not use saw blades made of high speed steel.

5. Do not use saw blades which do not comply with the

characteristics specifi ed in these instructions.

6. Do not stop the saw blades by lateral pressure on the

disc.

7. Always keep the saw blades sharp.

8. Ensure that the lower guard moves smoothly and freely.

9. Never use the circular saw with its lower guard fi xed in

the open position.

10. Ensure that the retraction mechanism of the guard

system operates correctly.

11. The saw blades body must be thinner than the riving

knife and the width of cut, or kerf (with teeth set) must be

greater than the thickness of the riving knife.

12. Never operate the circular saw with the saw blade turned

upward or to the side.

13. Ensure that the material is free of foreign matters such as

nails.

14. The riving knife should always be used except when

plunging in the middle of the workpiece.

15. Disconnect the plug from the receptacle before carrying

out any adjustment, servicing or maintenance.

16. For models C6BU3, C6BUM, C7BU3 and C7BUM, be

careful of brake kickback.

C6BU3, C6BUM, C7BU3 and C7BUM models feature an

electric brake that functions when the switch is released.

As there is some kickback when the brake functions, be

sure to hold the main body securely.

17. Sparks can sometimes appear caused by braking

operation when the switch is turned off since C6BU3,

C6BUM, C7BU3 and C7BUM models employ electric

brakes. Be informed, however, that this phenomenon is

not a machine trouble.

18. For models C6BU3, C6BUM, C7BU3 and C7BUM,

when the brake becomes ineff ective, replace the carbon

brushes with new ones.

19. Ensure that the power source to be utilized conforms

to the power requirements specifi ed on the product

nameplate.

20. Before the tool is plugged in to the receptacle, ensure

that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

21. When the work area is removed from the power source,

use an extension cord of suffi cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

22. Since the saw blade will extend beyond the lower surface

of the lumber, place the lumber on a workbench when

cutting. If a square block is utilized as a workbench,

select level ground to ensure it is properly stabilized. An

unstable workbench will result in hazardous operation.

(Fig. 3)

To avoid possible accident, always ensure that the

portion of lumber remaining after cutting is securely

anchored or held in position.

23. Should knob remain loosened, it will create a very

hazardous situation. Always thoroughly clamp it. (Fig. 4)

24. It is very hazardous to allow wing bolt to remain loosened.

Always thoroughly clamp it. (Fig. 5)

25. Prior to cutting operation, make sure the material you

are going to cut. If the material to be cut is expected to

generate harmful / toxic dusts, make sure the dust bag

or appropriate dust extraction system is connected with

dust outlet tightly.

Wear the dust mask additionally, if available.

○ Before starting to saw, confi rm that the saw blade

has attained full-speed revolution.

○ Should the saw blade stop or make an abnormal

noise while operating, promptly turn OFF the switch.

○ Always take care in preventing the power cord from

coming near to the revolving saw blade.

○ Using the circular saw with the saw blade facing

upwards or sideways is very hazardous. Such

uncommon applications should be avoided.

○ When cutting materials, always wear protective

glasses.

○ When fi nished with a job, pull out the plug from the

receptacle.

26. After having attached the saw blade, reconfi rm that the

lock lever is fi rmly secured in the prescribed position.

27. Models C6U3, C6BU3, C7U3 and C7BU3 are equipped

with a blower function. However, do not use the tool for

the blower function only. (Fig. 8

)

28. Check that there are no nicks or scratches in the cord.

29. Check the exterior and ensure that there is no damage.

30. Use a chip saw that is for cutting wood.

31. Use a chip saw with a displayed speed that is equal to or

higher than the rotation speed displayed on the tool.

32. Do not leave the saw placed on top of the guide rail.

0000Book̲C6U3.indb40000Book̲C6U3.indb4 2017/12/0113:15:502017/12/0113:15:50

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Hikoki C 6U3 Cirkelsåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Hikoki. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Hikoki C 6U3 Cirkelsåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Hikoki Cirkelsågar
Fler bruksanvisningar för Cirkelsågar

Vanliga frågor om Hikoki C 6U3 Cirkelsåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Hikoki C 18DGL Cirkelsåg

Bruksanvisning

Hikoki C 6MEY Cirkelsåg

Bruksanvisning

Hikoki C 5MEY Cirkelsåg

Bruksanvisning

Hikoki C 18DBAL Cirkelsåg

Bruksanvisning

Hikoki C 6SS Cirkelsåg

Bruksanvisning

Hikoki C 18DBL Cirkelsåg

Bruksanvisning

Hikoki C 3605DYA Cirkelsåg

Bruksanvisning

Hikoki C 3605DA Cirkelsåg

Relaterade kategorier