Bruksanvisning Heco CELAN XT 501 Högtalare

Bruksanvisning

Dear HECO Customer,

Congratulations on your fine new loudspeakers and thank you very much for choosing HECO! You have

made an excellent choice. The high-quality speakers produced by HECO are renowned all over the world.

Please study the instructions and information below carefully before using your new loudspeakers.

GENERAL INFORMATION ABOUT CONNECTING YOUR HECO CELAN XT LOUDSPEAKERS

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent

impairment of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths

up to 3 m and at least 4 mm² for lengths above 3 m.

Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place

the loudspeakers in their planned positions and cut the cables to the right length. The cables for both

channels should always be exactly the same length.

Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than tinning

them with solder – insert them in the terminals and tighten the terminal screws firmly (fig. 1). Loudspeaker

cables with CE-compliant banana or single-pin plugs (4 mm) or forked fittings can also be used.

For good sound it is imperative that the cables must be connected in such a way that the speakers are

“in phase”. This means that the black negative terminals on the speakers (-) must be connected to the

negative (-) terminals on the amplifier, the red positive (+) speaker terminals to the positive (+) amplifier

terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a ridge

in the insulation.

Before switching on the system double-check all your connections and make sure that the terminal screws

are tight and that there are no short circuits caused by stray wire filaments – this could cause serious

damage to your amplifier!

HECO CELAN XT - BI-WIRING AND BI-AMPING

Connector panel on the Heco Celan XT loudspeakers:

The connector panels on the Celan XT speakers are equipped with 5 terminal screws, enabling bi-

wiring/bi-amping in addition to conventional connection to an amplifier. The upper terminals are connected

to the treble and mid-treble side of the crossover and the lower terminals to the bass side. An additional

connector terminal enables a 2dB treble boost option.

Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this

idea one step further and uses separate power amplifiers as well as separate cables for high and low

frequencies. Bi-amping in particular produces an additional improvement in sound reproduction quality.

For conventional connections, metal bridges are installed as standard to make the +2dB treble adjustment

active. The bridge can be switched to the linear setting by unscrewing the corresponding terminals. (Fig.2)

The terminals have to be removed for bi-wiring and bi-amping mode. Fig. 3 and fig. 4 show the connection

to the amplifier(s).

The right treble setting depends on the room, the positioning of the speakers and, of course, personal

taste. The +2dB setting is recommended for rooms with heavy upholstered furniture and curtains, for

example, which have a muffling effect.

THE HECO CELAN XT 301, 501, 701 AND 901 IN STEREO MODE

In the ideal configuration the speakers and the listening position should form an equilateral triangle. When

the left and right speakers are the same distance from the listening position their sound arrives at the same

time, resulting in a harmonious, natural music reproduction.

There should be a clear line of sight between the loudspeakers and the listening position. Any sound-

absorbing or reflecting obstacles in the path will distort the sound. When you install the loudspeakers the

following distances should be maintained:

GB

6

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Heco CELAN XT 501 Högtalare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Heco. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Heco CELAN XT 501 Högtalare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Heco Högtalare
Fler bruksanvisningar för Högtalare

Vanliga frågor om Heco CELAN XT 501 Högtalare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Heco CELAN XT CENTER 4 Högtalare

Bruksanvisning

Heco VICTA 301 Högtalare

Bruksanvisning

Heco VICTA 200 Högtalare

Bruksanvisning

Heco METAS XT 701 Högtalare

Bruksanvisning

Heco VICTA 201 Högtalare

Bruksanvisning

Heco METAS XT 301 Högtalare

Bruksanvisning

Heco CELAN 700 Högtalare

Bruksanvisning

Heco METAS XT 501 Högtalare

Relaterade kategorier