Bruksanvisning FERM WLM1002 Svarv
Behöver du en bruksanvisning för din FERM WLM1002 Svarv? Nedan kan du se och ladda ner PDF-bruksanvisningen gratis på svenska. Den här produkten har för närvarande 0 vanliga frågor, 0 kommentarer och har 0 röster. Om det här inte är bruksanvisningen du vill ha, vänligen kontakta oss.
Är produkten defekt och erbjuder bruksanvisningen ingen lösning? Gå till ett Repair Café för gratis reparationstjänster.
Bruksanvisning
Loading…
2 Ferm
Product: Ferm Wood turning lathe
Type FHB-940,art. nr. 460140
Ferm, Genemuiden, The Netherlands.
Sound pressure level (L
pa
) 82 dB(A)
Sound power level (L
wa
)
82 dB(A)
AB C
A: Hearing protection must be worn.
B: Eye protection must be worn.
C: Read the instruction manual.
SERIAL NUMBER
The serial number on the machine consists of the follo-
wing elements.
Serial nr.
1. LATHE SPECIFICATIONS
Spindle speeds: 480-850-1310-2120-3010 rpm.
Headstock: No.1 morse taper and threaded 3/4 - 16.
Tailstock: No.1 morse taper.
Overall dim.: 1375 x 400 x 308 mm
Weight: 38 kgs.
CAREFULLY READ THE INSTRUCTIONS
BEFORE YOU USE THE WOOD LATHE!
2. SPECIAL SAFETY RULES
BEFORE USING THE MACHINE:
1. Check the following before you use the machi-
ne:
- does the voltage of the machine correspond with
the mains voltage;
- are all parts of the machine well fixed.
2. Close the V-Belt housing.
3. Unplug the machine from the mains before changing
the speed or replacing the V-belt.
This machine must be earthed. lf not pro-
perly earthed this power tool can cause an
electrical shock. Be sure that your outlet is
earthed. lf you have any doubt have it chec-
ked by a quatified electrician.
ADDITIONAL SAFETY INSTRUCTIONS.
1. When turning between centres or on the faceplate al-
ways rough-out “out of round” workpieces at slow
speed. Running the Lathe too fast so that it vibrates
could cause the workpiece to be thrown from the lat-
he or the turning tool to be jerked from your hands.
2. Always rotate the workpiece by hand before turning
on the motor. lf the workpiece strikes the tool rest it
could split end be thrown out of the Lathe.
3. Do not allow the turning tool to ‘bite’ into the work-
piece which could result in splitting of the workpiece
or the workpiece being thrown from the lathe. Al-
ways position the tool rest above the centreline of
the Lathe for spindle turning. Do not apply the turning
tool to the workpiece below the level of the tool rest.
4. Do not run the Lathe in the wrong direction. This
could cause the turning tool to be thrown from your
hands. The Lathe must run in a direction so that the
centre of the workpiece is below the level of the tool
rest and turns towards you.
5. Before attatching a workpiece to the faceplate always
‘rough it out’ to as true round as possible. This will
minimise vibration while turning. Always fasten the
workpiece securely to the faceplate. Failure to per-
form these setup operations could cause the work-
piece to be thrown from the Lathe.
6. Avoid awkward hand positions where a slip could
cause a hand to move into the workpiece.
7. Remove all knots before installing workpiece be-
tween centres or on the faceplate.
8. Never leave the lathe work area, before the lathe has
come to a complete stop.
9. Do not lay your turning tools on the bench so that you
must reach over the revolving workpiece to select
them.
10. Keep your cutting tools sharp at all times. Special cau-
tion must be excercised when knots or voids are ex-
posed to the turning tool.
11. Think safety.
12. Complete hand sanding of between centres or face-
plate mounted workpieces before removing from the
lathe. Do not exceed the speed used for the last cut-
ting operation performed on the workpiece, in ac-
cordance with the speed chart.
!
ORDER NUMBER/YEAR OF CONSTRUCTION
UK
English
Ferm 51
Exploded
FHB-940
AVAILABLE SPARE PARTS FOR FHB-940
REF.NR. DESCRIPTION FERM NR.
45 V-BELT 800170
23 SWITCH 406103
3 MOTOR 406102
41 HEADSTOCK SPINDLE 406104
43 SPUR CENTRE 406105
55 QUICK-ACTING KEY 406106
57 TOOL SUPPORT HOLDER 406107
58 TOOL SUPPORT 406108
61 SREW HANDLE 406109
64 CUP CENTRE 406110
75 PUSHER 406111
V~/Hz W RPM MM MM
460140 FHB-940 230/50 370 480 - 3.010 940 152,5
ART.NR
TYPE
1'
Loading…
Betyg
Berätta vad du tycker om FERM WLM1002 Svarv genom att betygsätta den. Vill du dela med dig av dina åsikter om denna produkt eller ställa en fråga? Lämna en kommentar nederst på sidan.Mer om denna bruksanvisning
Vi förstår att det är trevligt att ha en pappersbruksanvisning för din FERM WLM1002 Svarv. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar FERM. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din FERM WLM1002 Svarv på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.
Specifikationer
| Märke | FERM |
| Modell | WLM1002 |
| Kategori | Svarvar |
| Filtyp | |
| Filstorlek | 1 MB |
Alla bruksanvisningar för FERM Svarvar
Fler bruksanvisningar för Svarvar
Delta i konversationen om denna produkt
Här kan du dela vad du tycker om FERM WLM1002 Svarv. Om du har en fråga, läs först noggrant igenom manualen. Att begära en manual kan göras genom att använda vårt kontaktformulär.