Bruksanvisning FERM TDM1010 Bänkborrmaskin

Bruksanvisning

54 Ferm

SPARE PARTS LIST FTB-16

REF NR DESCRIPTION FERM NR

28 SPRING-TERSION 311106

29 CAP-SPRING 311107

38 MOTOR 311103

59 V-BELT 311104

2 RACK 311108

64 SWITCH 311105

79 KEY-DRIFT 311109

10 ARBOR 311110

11 CHUCK 311111

FLOOR PILLAR DRILL

THE NUMBERS IN THE FOLLOWING TEXT COR-

RESPOND WITH THE PICTURES AT PAGE 2

TECHNICAL SPECIFICATIONS

PRODUCT INFORMATION

Fig.A

1. On/off switch

2. Drill depth gauge

3. Protection guard

4. Motor

5. Drill depth lever

6. Table adjustment

Check first whether or not the delivery has been dama-

ged by transport and/or whether all the parts are pre-

sent.

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of the

instructions in this manual.

Denotes risk of electric shock.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Keep these instructions in a safe place!

Before using the machine the guidelines must be taken

into consideration. Every mechanical or electrical altera-

tion to the machine which does not meet the applicable

guidelines carries a considerable accident risk.

DURING USE THE FOLLOWING POINTS

MUST BE CONSIDERED:

• Do not remove any mechanical or electrical protec-

tive provisions.

• Check whether all the protective provisions are in

place and have been attached correctly.

• Wear safety goggles during drilling.

• If you have long hair, be sure to wear hair protection

(hair net or cap). Long hair can easily be caught in

moving parts.

• Wear fitted clothing; tie buttons on sleeves.

• Do not hold any workpieces in your hands when dril-

ling. Always use a machine clamp or another clamping

tool.

• Protect workpieces and clamping tools on the bench

to prevent them from getting caught. Fasten them

yourself with screws or clamp them to a machine

clamp fastened to the table.

• Check whether the drill holder is tightened properly.

• Check whether cable lead-throughs are okay.

• To remove drill chips only use hand brushes, brushes,

rubber wipers, chip hooks or similar aids.

• Do not carry out any cleaning or greasing work while

the machine is in operation.

• Always keep V-belts covered (so that your hands

cannot become caught).

• Only tighten the toothed ring drill holder by means of

the wrench.

• Never leave the wrench of the drill holder in the drill

holder! Before switching on the machine, check

whether the wrench really has been removed!

• Do not use any drills which are damaged on the

shank.

• Drill is not suitable to use as press!

• If the mains cable is damaged, it may only be replaced

by a mains cable of the same type.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

Voltage | 400 V

Frequency | 50 Hz

Power input | 400 W

No load speed | 220-2500/min

Number of speeds | 12 (L/R)

Chuck capacity/Morse Conisch | 16 mm/MC-2

Weight | 60 kg

Lpa (sound pressure level) | 63.4 dB(A)

Lwa (sound power level) | 76.4 dB(A)

Vibration value | 0.757 m/s

2

UK

English

Ferm 3

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din FERM TDM1010 Bänkborrmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar FERM. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din FERM TDM1010 Bänkborrmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för FERM Bänkborrmaskiner
Fler bruksanvisningar för Bänkborrmaskiner

Vanliga frågor om FERM TDM1010 Bänkborrmaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

FERM TDM1001 Bänkborrmaskin

Bruksanvisning

FERM TDM1008 Bänkborrmaskin

Bruksanvisning

FERM TDM1002 Bänkborrmaskin

Bruksanvisning

FERM TDM1012 Bänkborrmaskin

Bruksanvisning

FERM TDM1006 Bänkborrmaskin

Bruksanvisning

FERM TDM1007 Bänkborrmaskin

Bruksanvisning

FERM TDM1021 Bänkborrmaskin

Bruksanvisning

FERM TDM1003 Bänkborrmaskin

Relaterade kategorier