Bruksanvisning FERM RSM1001 Tigersåg

Bruksanvisning

46 Ferm

SPARE PARTS LIST FRS-600

REF NR DESCRIPTION FERM NR

001 ADJUSTABLE BOTTOM PLATE 408500

002 GUARD PLATE 408501

003 RUBBER SLEEVE 408502

007 BLADE HOLDER 408503

014 RECIPROCALING BAR 408504

015 SLIDING BEARING 408505

019 ADJUSTING SPEED PLATE 408506

021 large cover sheet 408507

024 ROLLER BEARING 408508

027 ROLLER SHAFT 408509

028 GEAR WHEEL 408510

029 WASHER 408511

030 CENTRE COLUMN 408512

032 CARBON BRUSH SET 408513

033 CARBON BRUSH HOLDER 408514

037 SWITCH 408515

052 ROTOR 408516

057 STATOR 408517

RECIPROCATING SAW

THE NUMBERS IN THE FOLLOWING TEXT COR-

RESPOND WITH THE PICTURES AT PAGE 2

TECHNICAL SPECIFICATIONS

PRODUCT INFORMATION

Fig.A

1. Blade

2. F ootplate

3. Blade clamp screw

4. Trigger switch

5. Speed controller

6. Trigger lock button

7. Mains lead

8. Footplate length adjustment screws

9. 3 mm hexagon key (not s hown)

10. 4 mm hexagon key (not shown)

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of the

instructions in this manual.

Denotes risk of electric shock.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Keep these instructions in a safe place!

ADDITIONAL SAFETY INSTRUCTIONS

The machine must not be damp and must not be

operated in a wet environment. Always inspect

cable and plug before using machine. Only have

damage repaired by a qualified professional.

Only insert the plug into the mains socket when the

machine is switched off. Wear protective gloves and

sturdy footwear.

Do not saw materials containing asbestos!!!

• Wear protective goggles when working with mate-

rials which produce large amounts of chips.

• Wear a protective mask when sawing other fibrous

materials.

• Portable equipment used outdoors must be connec-

ted with a fault-current circuit breaker.

• Extension cables and plugs must be approved for out-

doors.

• Remove adjusting keys and wrenches before turning

the tool on.

• Secure your workpiece with clamps. Always lead

cable away from machine towards the rear.

• Move machine towards the workpiece only when

switched on.

• Always hold machine with both hands and ensure

that you have a safe footing while working.

• The machine may be operated only with the foot

plate mounted. When sawing, the foot plate must

always rest on the workpiece.

• Always remove the plug from the mains socket

before carrying out any work on the machine.

• Do not carry the machine by the cable.

• Incorrect handling may damage the machine. There-

fore always comply with the following instructions.

• Use only sharp saw blades in perfect condition;

replace cracked, distorted or blunt saw blades imme-

diately.

• Machine should only be switched on with blade

installed

• Select tools, stroke rate and pendulum actions

according to material, Take care to maintain a con-

stant reed rate.

• Do not attempt to stop the saw blade with lateral

pressure after switching off.

• Only use genuine accessories.

• Always use the correct supply voltage. The voltage

specifications on the rating plate must correspond

with the mains voltage. Equipment marked with 230

V can also be connected to 220-240 V.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Excessive sparking of the carbon brushes and vertici-

liosis in the collector.

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defect switch.

• Smoke or stench of scorched insulation.

Voltage | 230 V~

Frequency | 50 Hz

Power input | 600 W

No load speed | 300-2000/min

Maximum cutting thickness | 115 mm

Stroke length | 30 mm

Weight | 3.3 kg

Lpa (sound pressure level) | 86 dB(A)

Lwa (sound pressure capacity) | 99 dB(A)

Vibration value | 8.9 m/s

2

UK

English

Ferm 3

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din FERM RSM1001 Tigersåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar FERM. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din FERM RSM1001 Tigersåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för FERM Tigersågar
Fler bruksanvisningar för Tigersågar

Vanliga frågor om FERM RSM1001 Tigersåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

FERM RSM1008 Tigersåg

Bruksanvisning

FERM RSM1014 Tigersåg

Bruksanvisning

FERM RCM1001 Tigersåg

Bruksanvisning

FERM RSM1010 Tigersåg

Bruksanvisning

FERM RSM1015 Tigersåg

Bruksanvisning

FERM RSM1002 Tigersåg

Bruksanvisning

FERM RSM1013 Tigersåg

Bruksanvisning

FERM RCM1002 Tigersåg

Relaterade kategorier