Bruksanvisning FERM PDM1026 Slagborrmaskin

Bruksanvisning

Ferm 45

• Always compare the maximum rotation speed of

accesoires with the maximum speed of the

percussion drill.

• Pull the mainsplug from the socket before you

change a drill or accessory.

WHEN OPERATING THE MACHINE:

• Check if the switch is placed in the ‘OFF’-position

before you connect the machine to mains.

• Keep the mains cable away from moving parts of the

machine.

• First switch off the machine before you move the

machine downwards along your body.

• Never cover the ventilation slots.

IMMEDIATELY SWITCH OFF THE

MACHINE IN CASE OF:

• Excessive sparking of the brushes and verticiliosis in

the collector.

• Malfunction of the mainsplug, -socket or damaged

cables.

• Broken switch.

• Smoke or smell caused by scorched insulation.

3. BEFORE OPERATING THE

MACHINE

Use only sharp drills of the following types

Fig.B

Concrete/masonry

|

Hard metal

Metal

|

HSS

Wood

|

HSS

MOUNTING ACCESSORIES

Fig.C

Prior to mounting an accessory always unplug the

tool.

Placing and removing bits

In addition to bits the machine can also hold screw bits

with a hexagonal shaft.This is done as follows:

• Hold the drill head (A) and slide the ring (B) in the

direction of the drilling machine.

• Place the shaft of the bit in the nesting place of the

drill chuck. Tighten the bit by holding ring B and

turning the drill head (A).

• Once the bit has been tightened in, slide ring B in the

direction of the drill head. This will stop the drill head

from loosening due to vibration during use.

• Slide the sidegrip over the drillhead.

• Slide the measuring rod in the sidegrip and tighten

the grip by turning the sidegrip.

• Tighten the workpiece to a workbench by using a

clamp.

• When all preparations are done the machine can be

connected to mains. First check if the switch is in the

‘OFF’-position and if the rotationswitch is in the

RIGHT-position.

4. OPERATION

THE ON/OFF SWITCH

Fig.D

• Switch the machine on by pressing the triggerswitch

(A). When you release the triggerswitch (A) the

machine will turn off.

SWITCH-LOCK

• You can lock the On/Off switch by pressing the

triggerswitch (A) and then pressing knob (B). Release

the switch-lock by pressing the triggerswitch (A)

shortly.

SPEED-CONTROL

• The rotation-speed can be continuously adjusted

between 0 and 2500 rotations per minute, by

pressing the switch (A) deeper or less deep.

ADJUSTING OF THE MAXIMUM

ROTATIONSPEED

• Switch the machine on by pressing triggerswitch (A).

• Lock the triggerswitch (A) by pressing knob (B).

• Adjust the speed by turning the small wheel (C) to

the desired maximum rotation speed.

SWITCHING THE DIRECTION OF

ROTATION

• Direction of rotation counter-clockwise: shift

switch (D) to “L”.

• Direction of rotation clockwise: shift switch (D) to

“R”.

SWITCH FOR PERCUSSION DRILLING

Fig.E

• Slide the switch to the “Drill” symbol for normal

drilling.

• Slide the switch to the “Hammer” symbol for

percussion drilling.

MALFUNCTION

Below we have listed a number of possible causes and

corresponding solutions in case the machine does not

function as it should:

1. Excessive sparkling

• This usely indicates dirt in the motor or worndown

carbon brushes.

- Bring your percussion drill to your Ferm-dealer.

2. The percussion drill is overheating

• The ventilationslots are covered with dirt.

- Clean them with a dry cloth.

• The percussion drill is overloaded.

- Use the machine for work for which it is ment to be.

- Replace the drill for a sharp one or sharpen the drill by

using a benchgrinder and a twist drill grinding

attachment.

• The motor is defect.

- Bring your percussion drill to your Ferm-dealer for

repairance.

4 Ferm

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din FERM PDM1026 Slagborrmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar FERM. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din FERM PDM1026 Slagborrmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för FERM Slagborrmaskiner
Fler bruksanvisningar för Slagborrmaskiner

Vanliga frågor om FERM PDM1026 Slagborrmaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

FERM PDM1005 Slagborrmaskin

Bruksanvisning

FERM CDM1079 Slagborrmaskin

Bruksanvisning

FERM PDM1020 Slagborrmaskin

Bruksanvisning

FERM PDM1027 Slagborrmaskin

Bruksanvisning

FERM PDM1016 Slagborrmaskin

Bruksanvisning

FERM PDM1051 Slagborrmaskin

Bruksanvisning

FERM PDM1003 Slagborrmaskin

Bruksanvisning

FERM PDM1039 Slagborrmaskin

Relaterade kategorier