Bruksanvisning FERM AGM1023 Vinkelslip

Bruksanvisning

12 Ferm

• Ensure that blotters are used when they are

provided with the bonded abrasive product and

when they are required.

• If a guard is supplied with the tool never use the tool

without such a guard.

• For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length.

• Ensure that ventilation openings are kept clear when

working in dusty conditions. If it should become

nessesary to clear dust, first disconnect the tool

from the mains supply (use non metallic objects) and

avoid damaging internal parts.

• Though poor conditions of the electrical mains,

shortly voltage drops can appear when starting the

equipment. This can influence other equipment (eq.

blinking of a lamp). If the mains-impedance Zmax

<0.348 Ohm, such disturbances are not expected.

(In case of need, you may contact your local supply

authority for further information.

Electrical safety

Always check that the power supply corresponds to

the voltage on the rating plate.

Your machine is double insulated in accordance

with EN50144; therefore no earthwire is required.

Replacing cables or plugs

Immediately throw away old cables or plugs when they

have been replaced by new ones. It is dangerous to insert

the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm

2

. When using a cable reel always unwind

the reel completely.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always unplug the

tool.

Removing and mounting the guard

Fig.B

Replace the guard only with one of sheet steel or

material of equal strength.

Disassembly

• Remove the flange nut and the flange from the

spindle (2).

• Turn the screw (3) in the protective guard (1)

counterclockwise with help of a crosshead

screwdriver.

• Remove the machine’s protective guard.

Assembly

• Put the protective guard (1) on the machine.

• Turn the protective guard (1) to the position

indicated in the drawing.

• Turn the screw (3) in the protective guard clockwise

with help of a crosshead screwdriver.

• Put the flange nut and the flange back on the spindle (2).

Mounting a grinding disc

Fig.C

Use grinding discs of the correct dimension. Use fibre

reinforced grinding discs only. The grinding disc must

not touch the edge of the guard.

• Press the spindle lock and turn the spindle (9) until it

engages in the lock. Keep the spindle lock pressed

during this procedure.

• Remove the flange nut (12) from the spindle using the

spanner (11).

• Position the grinding disc (7) on the flange (5).

• Place the flange nut on the spindle an tighten it using

the spanner.

• Release the spindle lock and check that the spindle is

unlocked by rotating it.

Mounting the side handle

The side handle can be used for both left-hand and right-

hand control.

• Fasten the side handle (Fig. A-3) for left-hand

operation on the right-hand side of the machine.

• Fasten the side handle for right-hand operation on

the left-hand side of the machine.

• Fasten the side handle for upright working at the top

of the machine.

Make sure that the side handle is fastened

properly and cannot loosen unexpectedly.

4. USE

Always observe the safety instructions and

applicable regulations.

Do not place the machine on the workpiece when

switching the machine on or off. The grinding disc may

damage the workpiece.

• Clamp the workpiece and make sure that the

workpiece cannot slide from under the machine

during the cutting activities.

• Hold the machine firmly and press it under an angle of

approximately 15˚ against the workpiece. Move the

grinding disc evenly across the workpiece.

• Regularly inspect the grinding disc. Worn grinding

discs have a negative effect on the efficiency of the

machine. Replace a grinding disc on time.

• Always switch off the machine first before removing

the plug from the wall socket.

Switching on and off

• Slide the on/off switch forwards.

• To switch off, depress the on/off switch, this will then

jump to the ‘off’ position.

Do not put the machine down when the motor is still

running. Do not place the machine on a dusty surface.

Dust particles may enter the mechanism.

Ferm 5

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din FERM AGM1023 Vinkelslip. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar FERM. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din FERM AGM1023 Vinkelslip på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för FERM Vinkelslipar
Fler bruksanvisningar för Vinkelslipar

Vanliga frågor om FERM AGM1023 Vinkelslip

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

FERM AGM1016 Vinkelslip

Bruksanvisning

FERM AGM1061S Vinkelslip

Bruksanvisning

FERM AGM1029 Vinkelslip

Bruksanvisning

FERM AGM1098P Vinkelslip

Bruksanvisning

FERM AGM1026 Vinkelslip

Bruksanvisning

FERM AGM1031 Vinkelslip

Bruksanvisning

FERM AGM1087 Vinkelslip

Bruksanvisning

FERM AGM1025 Vinkelslip

Relaterade kategorier