Bruksanvisning Falcon PC 1000 Köksfläkt

Bruksanvisning

Mercury Cooker Hoods: PC1000/1082/1100/1200

Revision: 22/11/2012

2

ENGLISH

SECTION 1. INTRODUCTION

Your range cooker is a semi-professional unit which gives you the power and flexibility to realise your full

potential in the kitchen. Inevitably, during the cooking process, there will be heat, vapours and fumes

produced. Your Falcon extractor has been designed to complement the range cooker both in looks and

performance in order to create the ideal environment for creative cooking.

SECTION 2. EXTRACTION PERFORMANCE

The most important influence on the performance of the extractor is the design of the ducting which

takes the exhaust air from the extractor to the outside wall louvre. The duct route should be a prime

consideration during the initial stages of the kitchen design. Please note the following:

•

The extractor is provided with a spigot suitable for connecting 150mm diameter duct.

•

Note: 150mm is the minimum duct diameter consistent with efficient extraction.

•

The exhaust duct route length should be kept as short as possible with as few bends as possible.

•

The most efficient configuration is to duct straight through an outside wall so try to position the

cooker against an outside wall when designing your kitchen layout.

•

The hood can be vented either to the top exhaust or the rear exhaust position. Use the position

which gives the shortest duct route length and least number of bends. (The blower will need to be

rotated for ducting directly through the rear exhaust position.)

•

A route with more than two 90 bends will significantly degrade the performance of the extraction

system. If possible, avoid having a 90 bend at the extractor exhaust spigot; keep bend radii as

large as possible to maintain a smooth airflow without vortices; avoid kinks in flexible ducting; pull

flexible ducting taut over straight runs to ensure that the internal surface is as smooth as possible.

SECTION 3. IMPORTANT INFORMATION

The following minimum headroom is required to accommodate the cooker and hood:

For a small charge customised replacement chimneys can be produced to suit your requirements.

The minimum distance between the range hob burners and the bottom of the extractor is essential to

prevent overheating of the extractor and its components.

If you are fitting a splashback then the cooker-to-hood clearance is dictated by the splashback height.

Please also note that a 90 bend in the flexible ducting will require 215mm minimum headroom to give a

smooth radius with no kinking.

Requirements of the relevant authorities concerning the discharge of exhaust air must be complied with.

Attention:

This appliance requires an earth connection.

Ensure that the supply voltage corresponds to that marked on the rating label inside the extractor.

The extractor must be isolated from the electrical supply before carrying out any cleaning or mainte-

nance operations.

Pay particular attention to fire risk when frying. To minimise the risk of fire, all instructions

relating to cleaning the grease filters and removing grease deposits must be adhered to.

Do not flambé under the extractor.

SECTION 4. INSTALLATION

4.1 Removing the Grease Filter(s)

Place extractor on its backplate on a horizontal surface.

To remove the grease filters pull/lift the filter release lever away from the hood base. This releases the

retaining clips allowing the filter to be carefully lifted away from the hood. Take care not to scratch the

hood.

The internal fixing holes, blower assembly and spigot blanking plate can now be accessed through the

openings in the baseplate. (See Page 7).

4.2 Blower Exhaust Position

The hood can be vented either to the top exhaust or the rear exhaust position. Each exhaust position

has 4 studs onto which can be bolted either the blower assembly or a blanking plate.

Bolt blower assembly to chosen exhaust position and the blanking plate to the unused position.

When changing the exhaust position, care should be taken not to excessively pull or twist the cable

attached to the blower.

4.3 Duct Installation

Make a hole in the wall or ceiling to take the 150mm diameter ducting from the extractor exhaust spigot

to the outside.

The exhaust duct route length should be kept as short as possible with as few bends as possible - see

Section 2.

Knock a hole in the outside wall to match the internal measurements of the louvre.

4.4 Fixing the Hood to the Wall

If you are fitting a Splashback it must be fitted before the hood.

Instructions for mounting the hood are given on page 7

Note: The decorative chimney can be removed to ease handling of the hood.

The supporting wall must be of good quality, have an even surface and be sturdy enough to support the

extractor.

Fixings must be used which are suitable for the type of wall construction.

4.5 Connecting the Ducting

Connect ducting to extractor exhaust spigot. This may have to be done prior to fixing the extractor to the

wall. You may find this easier with the chimney removed. The chimney is attached using M4 machine

screws which can be accessed through the filter opening(s).

When the extractor is in position, check that the duct has not been flattened or kinked along its route.

Connect the ducting to the wall louvre spigot or alternative outside termination.

Secure the louvre to the outside wall. Ensure that any air fins are directed downwards.

Refit the grease filter(s).

4.6 Electrical Installation

The extractor is a stationary appliance designed to be connected by fixed wiring to the electrical supply.

A competent electrical technician must perform the electrical installation.

The extractor must be fed from a 230Vac single phase electrical supply using a switched spur fitted with

a 3A fuse. The spur should be located adjacent to the extractor/cooker so that the supply can be discon-

nected from the extractor using the switch. The means of disconnecting from the supply must have a

minimum contact separation of 3mm in all poles. Alternatively a means of disconnection in the fixed

wiring according to the relevant wiring rules must be fitted.

A supply cord for connecting the spur to the extractor is included.

The mains supply is connected to the free end of this cord as follows:

SECTION 5. OPERATING INSTRUCTIONS

a. Switch power on at the fused spur.

b. The extractor has 6 push-buttons which illuminate when selected. Their functions are summarised

in the table below.

c. The extractor controller will automatically switch off the appliance if there has been no operator

action for 4 hours.

d. After 30 hours accumulated running GREASE FILTER SATURATION will be signalled by all 6

indicators flashing. Reset by pressing Push-button FAN OFF (delay).

SECTION 6. MAINTENANCE

Regular maintenance is essential to ensure good performance and long-life.

To clean the stainless steel surfaces of the extractor use a proprietary cleaning agent. Do not use

abrasive cleaning materials or products.

Clean the grease filters in a dishwasher or by hand-washing in hot water and detergent. Wash the filters

at least every 2 months - sooner if the extractor is used extensively.

To remove the grease filters pull the chrome effect filter release lever away from the hood base. This

releases the retaining clips allowing the filter to be carefully lifted away from the hood. Care should be

taken not to scratch the hood.

To maintain the immaculate appearance of the extractor, and to minimise fire risk, ensure that grease

deposits on the extractor surfaces are kept to a minimum by regular cleaning.

To access the halogen lamps for replacement lever off the chrome ring immediately surrounding the

matt glass with a screwdriver. Only replace with bulbs of the same type and rating.

SECTION 7. SPECIFICATIONS

Hood Weights (Approximate)

Cooker-to-hood clearance (min): 800 mm

Hood height including chimney: 511—762 mm

Minimum ceiling height with standard chimney: 2251mm

Warning

Proper care must be taken to ensure that the negative pressures caused by high performance

extraction systems do not adversely affect the safe operation of certain types of fuel-burning

appliances (gas, oil or solid fuel), including those installed in the kitchen and possibly also those

installed in other parts of the house.

Where such fuel-burning appliances are installed, adequate ventilation MUST be provided in the

room of installation, located and sized such that the negative pressure in the room created by the

extractor does not exceed 4Pa.

In case of doubt, do not operate the extractor and fuel-burning appliance(s) simultaneously and

consult an appropriate (for the fuel type) expert for advice.

The exhaust air must not be discharged into a flue which is used for exhausting fumes from appli-

ances supplied with energy other than electricity, e.g. oil or gas-fired central heating boilers, gas-

fired water heaters, etc.

Adequate ventilation of the room must be provided when the cooker, extractor and appliances

supplied with energy other than electricity (e.g. gas-fired or oil-fired heaters, etc.) are used simulta-

neously. The room must be provided with vents to allow a constant flow of fresh air.

ELECTRICAL HAZARD

DISCONNECT ELECTRICAL SUPPLY

BEFORE PROCEEDING FURTHER

INCOMING SUPPLY CORD CONNECTIONS

Core

Core Colour

Live Brown

Neutral Blue

Protective Earth Green/Yellow

Blower airflow, nominal:

1000 m

3

/hr

Noise level:

52dBA

Supply voltage:

230V~ 50Hz

Halogen lamp voltage:

12V

Blower power input:

1 @ 250W

Halogen lamp power:

2 x 20W

Total power:

290W

Fuse size for electrical supply:

3A

Blower spigot diameter:

150mm

PC1000

28Kg

PC1082/1100

29Kg

PC1200

29.5Kg

Pushbutton Function

LIGHTS ON/OFF

0 1

FAN ON SPEED 1 (min);

FAN OFF (immediate stop).

2 FAN ON SPEED 2

3 FAN ON SPEED 3

4 FAN ON SPEED 4 (max)

FAN OFF AFTER 10 MINUTE DELAY to clear residual fumes;

indicator flashes during time-out.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Falcon PC 1000 Köksfläkt. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Falcon. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Falcon PC 1000 Köksfläkt på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Falcon Köksfläktar
Fler bruksanvisningar för Köksfläktar

Vanliga frågor om Falcon PC 1000 Köksfläkt

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Falcon SC 1082 Köksfläkt

Bruksanvisning

Falcon Contemporary Köksfläkt

Bruksanvisning

Falcon SC 1200 Köksfläkt

Bruksanvisning

Falcon PC 1200 Köksfläkt

Bruksanvisning

Falcon SC 1000 Köksfläkt

Bruksanvisning

Falcon Hi-LITE Köksfläkt

Bruksanvisning

Falcon PC 1082 Köksfläkt

Bruksanvisning

Falcon Super Köksfläkt

Relaterade kategorier