Bruksanvisning Cocraft L350 Kompressor

Bruksanvisning

ENGLISH

7

Motor overload cut-out

If thesafety cut-out has tripped, themotor has been overloaded in some way.

Thebutton on themotor overload cut-out (1) will pop out acouple of

millimetres when it has been tripped and is reset by pushing it back in.

There are anumber of possible reasons why theoverload cut-out might

trip such as avoltage drop caused by theuse of long extension leads, low

ambient temperature (under 10°C), or that thepressure switch is not used

to turn thecompressor on/off in theevent of apower cut for example.

Care and maintenance

• Thecompressor’s first oil change should be done after 10 hours of operation.

• Change theoil and clean theair filter after every 120 hours of use. Check thesafety valve and

pressure gauges at thesame time.

• Pull thespring-loaded ring to check thesafety valve. If thesafety valve is working properly

(and thepressure vessel is under pressure) air should seep out through thesafety valve.

• Perform avisual inspection at least once ayear to check that theinside and outside of

thepressure vessel is free of corrosion. Under no circumstances must thewall thickness of

thepressure vessel be less than 2 mm.

• Thesafety valve must under no circumstances be manipulated or blocked.

• Regularly check that theventilation port in theoil filler cap (11) is open.

• Regularly check that all bolts holding thecompressor and pressure vessel together are tight.

• Make it ahabit to open thedrain tap (9) to release any trapped condensation in thepressure

vessel.

• Do not clean thecompressor or pressure vessel with solvents or flammable liquids.

• If thecompressor is not to be used for anextended period: Unplug it from themains, empty

thepressure vessel and drain it using thedrain tap (9).

Changing the oil

1. Turn off and unplug thecompressor from thewall socket before changing theoil.

2. Remove theoil filler plug (11).

3. Tilt thecompressor so that oil can run out of theoil filler hole into anappropriate receptical.

4. Let theoil completely drain from thecompressor.

5. Replace with new oil until theoil reaches themiddle of theoil-display window. Refit theoil

filler plug.

Oil capacity: Approx 1 dl.

• Use SAE 30 compressor oil at temperatures above +10°C.

• Use SAE 10 compressor oil at temperatures below +10°C.

Compressor oil is especially designed for compressors, e.g. it has additives that prevent foaming.

If no compressor oil is available then SAE 10-30 engine oil can be used as asubstitute.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Cocraft L350 Kompressor. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Cocraft. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Cocraft L350 Kompressor på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Cocraft Kompressorer
Fler bruksanvisningar för Kompressorer

Relaterade produkter

Bruksanvisning

Cocraft DZ-2025F Kompressor

Bruksanvisning

Cocraft JL811001 Kompressor

Bruksanvisning

Cocraft L224 Kompressor

Bruksanvisning

Cocraft EZ-3050V/10-L Kompressor

Bruksanvisning

Metabo Mega 350-100 W Kompressor

Bruksanvisning

Senco AC4504 Kompressor

Bruksanvisning

Metabo Power 180-5 W OF Kompressor

Bruksanvisning

Michelin MBL 6V2/1100 Kompressor

Relaterade kategorier