Bruksanvisning Bort BWS-905-R Vinkelslip

Bruksanvisning

Angle grinder

INTENDED USE

This tool is intended for grinding, cutting and deburring

metal and stone materials without the use of water; with

the appropriate accessories the tool can also be used for

brushing and sanding

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1. Spindle

2. Clamping fl ange

3. Spanner

4. Spindle-lock button

5. Auxiliary handle

6. Safety guard

7. Mounting fl ange

8. On/off locking switch

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, fi re

and/or serious injury.

• Only use this tool for dry grinding/cutting

• Only use the fl anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

• Use the original SBM Group accessories which can be

obtained from your SBM Group dealer

• For mounting/using non- SBM Group accessories ob-

serve the instructions of the manufacturer concerned

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Do not use damaged, deformed or vibrating grinding/

cutting discs

• Handle and store grinding/cutting discs carefully to

avoid chipping and cracking

• Protect accessories from impact, shock and grease

• Do not use a grinding/cutting disc that is larger than the

maximum recommended size

• Only use grinding/cutting discs with a hole diameter

which fi ts mounting fl ange (7) without play; never use

reducers or adaptors to fi t large-hole grinding/cutting

discs

• Never use grinding/cutting discs with a threaded hole,

of which the thread is not long enough to accept the spin-

dle length of the tool

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

• Only use an extension cord which is intended for out-

door use and equipped with a splashproof coupling-sock-

et

BEFORE USE

• Before using the tool for the fi rst time, it is

recommended to receive practical information

• Do not work materials containing asbestos (asbestos is

considered carcinogenic)

• Take protective measures when during work dust can

develop that is harmful to one’s health, combustible or ex-

plosive (some dusts are considered carcinogenic); wear a

dust mask and work with dust/chip extraction when con-

nectable

• Be careful of hidden electrical wires or gas- and water

pipes; check the work area, for instance with a metal de-

tector

• Be careful when cutting grooves, especially in support-

ing walls (slots in supporting walls are subject to country-

specifi c regulations; these regulations are to be observed

under all circumstances)

• Clamp the workpiece in case it does not remain stationa-

ry from its own weight

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with

a capacity of 16 Amps (UK 13 Amps)

• Wear protective glasses and gloves, hearing protection

and sturdy shoes; when necessary, also wear an apron

• Always mount auxiliary handle (5) and protective guard

(6); never use the tool without them

• Be sure tool is switched off when plugging in

DURING USE

• Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug;

never use the tool with a damaged cord

• Push spindle-lock button (4) only when spindle (1) is at

a standstill

• Keep hands away from rotating accessories

• When grinding metal, sparks are generated; keep other

persons and combustible material from work area

• In case of electrical or mechanical malfunction, immedi-

ately switch off the tool and disconnect the plug

• In case the cutting disc is blocked, resulting in jerking

forces on the tool, immediately switch off the tool

• In case of current interruption or when the plug is ac-

cidentally pulled out, unlock the on/off switch (8) imme-

diately and put it in the OFF-position in order to prevent

uncontrolled restarting

• Do not apply so much pressure on the tool that it comes

to a standstill

AFTER USE

• Before you put down the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

• After switching off the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of this tool to the earth terminal of the

plug

6

English

+START

STOP

3

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Bort BWS-905-R Vinkelslip. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Bort. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Bort BWS-905-R Vinkelslip på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Bort Vinkelslipar
Fler bruksanvisningar för Vinkelslipar

Vanliga frågor om Bort BWS-905-R Vinkelslip

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Bort BWS-1400N Vinkelslip

Bruksanvisning

Bort BWS-901N Vinkelslip

Bruksanvisning

Bort BWS-600U Vinkelslip

Bruksanvisning

Bort BWS-2200U-S Vinkelslip

Bruksanvisning

Bort BWS-2000U-S Vinkelslip

Bruksanvisning

Bort BWS-1100N Vinkelslip

Bruksanvisning

Bort BWS-1700N Vinkelslip

Bruksanvisning

Bort BWS-1200U-SR Vinkelslip

Relaterade kategorier