Bruksanvisning Black and Decker KS1401L Cirkelsåg

Bruksanvisning

7

ENGLISH

Safety instructions for circular saws with outer or inner

pendulum guards and with tow guard

a. Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie the

lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and make sure it

moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

b. Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

c. Lower guard should be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts". Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

d. Always observe that the lower guard is covering the

bladebeforeplacingsawdownonbenchoroor.An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Additional safety instructions for all saws with riving knife

a.

Use the appropriate riving knife for the blade being

used. For the riving knife to work, it must be thicker than

the body of the blade but thinner than the tooth set of the

blade.

b. Adjust the riving knife as described in this instruction

manual. Incorrect spacing, positioning and alignment can

make the riving knife ineffective in preventing kickback.

c. Always use the riving knife except when plunge

cutting. Riving knife must be replaced after plunge

cutting. Riving knife causes interference during plunge

cutting and can create kickback.

d. For the riving knife to work, it must be engaged in the

workpiece. The riving knife is ineffective in preventing

kickback during short cuts.

e. Do not operate the saw if riving knife is bent. Even a

light interference can slow the closing rate of a guard.

Residual risks

The following risks are inherent to the use of saws:

- Injuries caused by touching the rotating parts.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts of the

rotating saw blade.

- Risk of injury when changing the blade.

- Risk of squeezing ngers when opening the guards.

- Health hazards caused by breathing dust developed

when sawing wood, especially oak, beech and MDF.

Saw blades

u Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specified in this

manual, complying with EN 847-1.

u Warning! Never use abrasive wheels.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Labels on tool

The following pictograms are shown on the tool:

:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Black and Decker KS1401L Cirkelsåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Black and Decker. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Black and Decker KS1401L Cirkelsåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Black and Decker Cirkelsågar
Fler bruksanvisningar för Cirkelsågar

Vanliga frågor om Black and Decker KS1401L Cirkelsåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Black and Decker KS865KN Cirkelsåg

Bruksanvisning

Black and Decker KS1300 Cirkelsåg

Bruksanvisning

Black and Decker KS65K Cirkelsåg

Bruksanvisning

Black and Decker KS55 Cirkelsåg

Bruksanvisning

Black and Decker KS1500L Cirkelsåg

Bruksanvisning

Black and Decker CS180 Cirkelsåg

Bruksanvisning

Black and Decker BES510 Cirkelsåg

Bruksanvisning

Black and Decker KS1301 Cirkelsåg

Relaterade kategorier