Bruksanvisning Black and Decker GK1830 Kedjesåg

Bruksanvisning

7

ENGLISH

(Original instructions)

u Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and

enables better control of the chainsaw in unexpected

situations.

u Only use replacement guide bars and chains

specified by the manufacturer. Incorrect replacement

guide bars and chains may cause chain breakage and/

or kickback.

u Follow the manufacturer's sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

u Striking metal, cement or any other hard material near

the wood, or buried in the wood can cause kickback.

u A dull or loose chain can cause kickback.

u Do not try to insert into a previous cut. As this could

cause kickback. Make a fresh cut every time.

Safety recommendations for the chainsaw

u We strongly recommend that first time users obtain

practical instruction in the use of the chainsaw and

protective equipment from an experienced user. Initial

practice should be completed sawing logs on a saw

horse or cradle.

u Always check that the kickback brake operates correctly

before use.

u We recommend that when carrying the chainsaw that

you make sure that the brake is engaged and the saw

chain is facing backwards.

u Maintain your chainsaw when not in use. Do not store

your chainsaw for any length of time without first

removing the saw chain and guide bar which should be

kept immersed in oil. Store all parts of your chainsaw in

a dry, secure place out of reach of children.

u We recommend you drain the oil reservoir prior to

storage.

u Be sure of your footing and pre-plan a safe exit from a

falling tree or branches.

u Use wedges to help control felling and prevent binding

the guide bar and saw chain in the cut.

u Saw chain care. Keep the saw chain sharp and snug on

the guide bar. Ensure the saw chain and guide bar are

clean and well oiled. Keep handles dry, clean and free

from oil and grease.

Avoid cutting

u Prepared timber.

u Into the ground.

u Into wire fences, nails. etc.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Electrical safety

#

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). The extension

cable must be suitable for outdoor use and marked

accordingly. Up to 30 m of HO7RN-F 2 X 1.5 mm²

extension cable can be used without loss of product

performance. Before use, inspect the extension cable for

signs of damage, wear and ageing. Replace the extension

cable if damaged or defective. When using a cable reel,

always unwind the cable completely.

Voltage drops

u Under certain power supply conditions this product may

cause short-time voltage drops during start-up.

u Other equipment may be affected. For example, electric

lights may temporarily reduce in brightness.

u Contact the supply authority, if necessary, to determine

that the impedance of the power supply is lower than

0.411 ohms. Disturbances are unlikely to occur under this

condition.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Black and Decker GK1830 Kedjesåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Black and Decker. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Black and Decker GK1830 Kedjesåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Black and Decker Kedjesågar
Fler bruksanvisningar för Kedjesågar

Vanliga frågor om Black and Decker GK1830 Kedjesåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Black and Decker GK2235 Kedjesåg

Bruksanvisning

Black and Decker GK2235T Kedjesåg

Bruksanvisning

Black and Decker GK1435 Kedjesåg

Bruksanvisning

Black and Decker CS1840 Kedjesåg

Bruksanvisning

Black and Decker GK1630T Kedjesåg

Bruksanvisning

Black and Decker GKC1817L Kedjesåg

Bruksanvisning

Black and Decker GK1530X Kedjesåg

Bruksanvisning

Black and Decker GPC1800P Kedjesåg

Relaterade kategorier