Bruksanvisning Black and Decker FS1806CSL Cirkelsåg

Bruksanvisning

3

tools, with sharp cutting edge are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on

another tool.

Service

• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

Specific Safety Rules

DANGER: Keep hands away from cutting area and blade. Keep your second

hand on auxiliary handle, or motor housing. If both hands are holding the saw, they

cannot be cut by the blade.

• Keep your body positioned to either side of the saw blade, but not in line with the

saw blade. KICKBACK could cause the saw to jump backwards. (See "Causes and

Operator Prevention of Kickback").

• Do not reach underneath the work. The guard cannot protect you from the blade below

the work.

• Check lower guard for proper closing before each use. Do not operate saw if lower

guard does not move freely and close instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally dropped, lower guard may be bent. Raise

the lower guard with the Retracting Lever and make sure it moves freely and does not

touch the blade or any other part, in all angles and depths of cut.

• Check the operation and condition of the lower guard spring. If the guard and the

spring are not operating properly, they must be serviced before use. Lower guard

may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

• Lower guard should be retracted manually only for special cuts such as "Pocket

Cuts" and "Compound Cuts". Raise the lower guard by Retracting Lever. As soon

as blade enters the material, lower guard must be released. For all other sawing, the

lower guard should operate automatically.

• Always observe that the lower guard is covering the blade before placing saw

down on bench or floor. An unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to

stop after switch is released.

• NEVER hold piece being cut in your hands or across your leg. It is important to

support the work properly to minimize body exposure, blade binding, or loss of control.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will also make

exposed metal parts of the tool "live" and shock the operator.

• When ripping, always use a rip fence or straight edge guide. This improves the

accuracy of the cut and reduces the chance for blade binding.

• Always use blades with correct size and shape (diamond vs. round) arbor holes.

Blades that do not match the mounting hardware of the saw will run eccentrically, causing

loss of control.

• Never use damaged or incorrect blade washers or bolts. The blade washers and bolt

were specially designed for your saw, for optimum performance and safety of operation.

Causes and Operator Prevention of Kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece toward the operator.

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back toward the operator.

• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the

blade can dig into the top surface of the wood causing the blade to climb out of the kerf

and jump back toward the operator.

• Kickback is the result of tool misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below:

90505019 FS Circ Saws 7/14/06 8:50 AM Page 3

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Black and Decker FS1806CSL Cirkelsåg. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Black and Decker. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Black and Decker FS1806CSL Cirkelsåg på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Black and Decker Cirkelsågar
Fler bruksanvisningar för Cirkelsågar

Vanliga frågor om Black and Decker FS1806CSL Cirkelsåg

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Black and Decker BDCS1400 Cirkelsåg

Bruksanvisning

Black and Decker KC1440SK Cirkelsåg

Bruksanvisning

Black and Decker KS855N Cirkelsåg

Bruksanvisning

Black and Decker CS1250L Cirkelsåg

Bruksanvisning

Black and Decker CS180 Cirkelsåg

Bruksanvisning

Black and Decker KS865KN Cirkelsåg

Bruksanvisning

Black and Decker CD600 Cirkelsåg

Bruksanvisning

Black and Decker KS840 Cirkelsåg

Relaterade kategorier