Bruksanvisning Black and Decker CD70CKA Slagborrmaskin

Bruksanvisning

4

ENGLISH

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could result

in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for impact drills

◆ Wear ear protectors with impact drills. Exposure to

noise can cause hearing loss.

◆ Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Additional safety instructions for Australia and

New Zealand

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Side handle

6. Chuck

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting the side handle (fig. A)

◆ Turn the grip (7) counterclockwise until you can slide the

side handle (5) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit (fig. B)

◆ Open the chuck by turning the front part (8) with one hand

while holding the rear part (9) with the other.

◆ Insert the bit shaft (10) into the chuck and firmly tighten

the chuck.

Removing and refitting the chuck (fig. C)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw (11), located in the

front part of the chuck, by turning it clockwise using a

screwdriver.

◆ Tighten an Allen key (12) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Before drilling into walls, floors or ceilings, check

for the location of wiring and pipes.

Selecting the direction of rotation (fig. D)

◆ For drilling and for tightening screws, place the forward/

reverse switch (3) in the neutral position.

◆ For loosening screws or removing a jammed drill bit, turn

the forward/reverse switch (3) to the left.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

◆ For drilling in masonry, set the drilling mode selector (4) to

the position.

◆ For drilling in other materials and for screwdriving, set the

drilling mode selector (4) to the position.

Switching on and off (fig. E)

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

As a general rule, use low speeds for large diameter drill

bits and high speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Black and Decker CD70CKA Slagborrmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Black and Decker. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Black and Decker CD70CKA Slagborrmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Black and Decker Slagborrmaskiner
Fler bruksanvisningar för Slagborrmaskiner

Vanliga frågor om Black and Decker CD70CKA Slagborrmaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Black and Decker KR653 Slagborrmaskin

Bruksanvisning

Black and Decker KD355RE Slagborrmaskin

Bruksanvisning

Black and Decker KD352RE Slagborrmaskin

Bruksanvisning

Black and Decker KR603 Slagborrmaskin

Bruksanvisning

Black and Decker CD501CRE Slagborrmaskin

Bruksanvisning

Black and Decker KR1102K Slagborrmaskin

Bruksanvisning

Black and Decker KR504CRES Slagborrmaskin

Bruksanvisning

Black and Decker KR999CK Slagborrmaskin

Relaterade kategorier