Bruksanvisning Whirlpool WDTA75SAHZ Diskmaskin

Bruksanvisning

3

Connected Appliance Regulatory Notices

Federal Communications Commission (FCC)

Compliance Notice

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

RF Exposure Information

To comply with FCC/IC RF exposure requirements for mobile transmitting

devices, this transmitter should only be used or installed at locations where

there is at least 20 cm separation distance between the antenna and all

persons.

To comply with FCC/IC RF exposure limits for general

population/uncontrolled exposure, the antenna(s) used for this transmitter

must be installed to provide a separation distance of at least 20 cm from all

persons and must not be co-located or operating in conjunction with any

other antenna or transmitter.

Industry Canada (IC) Compliance Notice

This Device complies with Industry Canada License-exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference,

2. This device must accept any interference, including interference that may

cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate

using an antenna of a type and maximum (or lesser) gain approved for the

transmitter by Industry Canada. To reduce potential radio interference to

other users, the antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

The radio transmitters IC: 10248A-WICHAM01 and 10248A-FLDAAM01

have been approved by Industry Canada to operate with the antenna types

listed below with the maximum permissible gain and required antenna

impedance for each antenna type indicated. Antenna types not included in

this list, having a gain greater than the maximum gain indicated for that type,

are strictly prohibited for use with this device.

Antenna Type

Maximum Permissible

Antenna Gain (dBi)

Required

Impendance (OHM)

Slot

1.2

50

Monopole

(WICHAM01 only)

0.5

50

Dipole

3.0

50

F

1.60

50

Planar F

4.2

50

To comply with FCC and Industry Canada RF radiation exposure limits for

general population, the antenna(s) used for this transmitter must be installed

such that a minimum separation distance of 20 cm is maintained between

the radiator (antenna) and all persons at all times and must not be co-

located or operating in conjunction with any other antenna or transmitter.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Conformément à la réglementation d’Industrie Canada, le présent émetteur

radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou

inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de

réduire les risques de brouillage radioélectrique à l’intention des autres

utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la

puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité

nécessaire à l’établissement d’une communication satisfaisante.

Le émetteurs radio IC : 10248A-WICHAM01 et 10248A-FLDAAM01 ont été

approuvés par Industrie Canada pour fonctionner avec les types d’antenne

énumérés ci-dessous et ayant un gain admissible maximal et l’impédance

requise pour chaque type d’antenne. Les types d’antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont

strictement interdits pour l’exploitation de l’émetteur.

Type d’antenne

Gain admissible

maximal d’antenne (dBi)

L’impédance

requise (OHM)

À fentes

1,2

50

Monopôle (WICHAM01

seulement)

0,5

50

Dipole

3,0

50

F

1,60

50

Planaire F

4,2

50

Pour satisfaire aux exigences de la FCC et IC d’exposition aux

radiofréquences, une distance de séparation de 20 cm ou plus doit être

maintenue entre cet appareil et des personnes lors de fonctionnement du

dispositif. Pour assurer la conformité des opérations au plus près que cette

distance n’est pas recommandée. L’antenne utilisée pour ce transmetteur

ne doit pas être co-localisés en conjonction avec toute autre antenne ou

transmetteur.

OEM Responsibilities to comply with FCC and

Industry Canada Regulations

The WICHAM01 / FLDAAM01 Modules have been certified for integration

into products only by OEM integrators under the following conditions:

1. The antenna(s) must be installed such that a minimum separation

distance of 20 cm is maintained between the radiator (antenna) and all

persons at all times.

2. The transmitter module must not be co-located or operating in

conjunction with any other antenna or transmitter.

As long as the two conditions above are met, further transmitter testing will

not be required. However, the OEM integrator is still responsible for testing

their end-product for any additional compliance requirements required with

this module installed (for example, digital device emissions, PC peripheral

requirements, etc.).

IMPORTANT NOTE: In the event that these conditions cannot be met

(for certain configurations or co-location with another transmitter), then the

FCC and Industry Canada authorizations are no longer considered valid and

the FCC ID and IC Certification Number cannot be used on the final product.

In these circumstances, the OEM integrator will be responsible for re-

evaluating the end product (including the transmitter) and obtaining a

separate FCC and Industry Canada authorization.

End Product Labeling

The WICHAM01 / FLDAAM01 Modules are labeled with FCC ID and IC

Certification Number. If the FCC ID and IC Certification Number are not

visible when the module is installed inside another device, then the outside

of the device into which the module is installed must also display a label

referring to the enclosed module. In that case, the final end product must be

labeled in a visible area or display the following:

“Contains FCC ID: A5UWICHAM01”

“Contains IC: 10248A-WICHAM01”

or

“Contains FCC ID: A5UFLDAAM01”

“Contains IC: 10248A-FLDAAM01”

The OEM of the WICHAM01 / FLDAAM01 Module must only use the

approved antenna(s), which have been certified with this module. The OEM

integrator has to be aware not to provide information to the end user

regarding how to install or remove this RF module or change RF related

parameters in the user manual of the end product.

The user manual for the end product must include the

following information in a prominent location:

“To comply with FCC and Industry Canada RF radiation exposure limits for

general population, the antenna(s) used for this transmitter must be installed

such that a minimum separation distance of 20 cm is maintained between

the radiator (antenna) and all persons at all times and must not be co-

located or operating in conjunction with any other antenna or transmitter.”

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Whirlpool WDTA75SAHZ Diskmaskin. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Whirlpool. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Whirlpool WDTA75SAHZ Diskmaskin på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Whirlpool Diskmaskiner
Fler bruksanvisningar för Diskmaskiner

Vanliga frågor om Whirlpool WDTA75SAHZ Diskmaskin

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Whirlpool ADP 4410 WH Diskmaskin

Bruksanvisning

Whirlpool WDT750SAHZ Diskmaskin

Bruksanvisning

Whirlpool ADP 7452 A+ 6S IX Diskmaskin

Bruksanvisning

Whirlpool WSFE 2B19 X UK N Diskmaskin

Bruksanvisning

Whirlpool WFO 3O41 PL X UK Diskmaskin

Bruksanvisning

Whirlpool WDF518SAHB Diskmaskin

Bruksanvisning

Whirlpool WH3UC10BS7A0W Diskmaskin

Bruksanvisning

Whirlpool WIS 1150 PEL Diskmaskin

Relaterade kategorier