Bruksanvisning Velleman K8200 3D-skrivare

Bruksanvisning

The 3D printer contains a lot of moving parts, but the force of the stepper motors is too low to cause serious injuries. Never-

theless it is recommended to provide additional protection against mechanical risks.

The easiest way to make your 3D printer “accident proof” is to put it inside a protective enclosure which completely covers

the 3D printer – with or without an access door and fume extraction. (numerous designs can be found on the internet)

To make it extra safe a switch which interrupts the power supply of the printer when the enclosure or door is opened can be

added. It is also advisable to install an external emergency stop switch, which also cuts off the power supply.

Providing adequate protection is the responsibility of the assembler.

Always cut power before maintenance or modication.

Mechanical safety and protection:

!

The 3D printer is not intended for use by persons (including children) with reduced physical, or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of

the appliance by a person responsible for their safety

Children should be supervised to ensure that they do not play with the appliance.

The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide.

The information in this document was obtained from sources which we believe are reliable.

However, the information is provided without any warranty, express or implied, regarding its correctness.

The conditions or methods used for assembling, handing, storage, use or disposal of the device are beyond our control and

may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability

for loss, injuries, damage, or expense arising out of or in any way connected with the assembly, handling, storage, use or

disposal of the product.

General safety information:

There is a potential risk of burns as the Printer head (extruder) can reach up to 270°C.

The use of common sense should be sufcient to prevent burns, but in some environments it is highly recommended to

provide additional protection. (see § Mechanical safety and protection)

The max. temperature of the heated bed is 60°C, this is below the 1 min. burn threshold for plastic surfaces according to

CENELEC Guide 29. Normal reexes prevent long contact periods with hot surfaces

Always let the 3D printer cool down for 60 min. before maintenance or modication.

Risk of burns:

!

This printer is designed for use with PLA and ABS lament (MSDS for the Velleman lament is available).

PLA: is a safe and non-toxic material, there are no known health safety risks when used in 3D printers.

ABS: when printing with ABS there is a distinctive ‘burned plastic’ smell. This is quite normal but it may also cause head-

aches, respiratory- and eye irritation with sensitive people (although it is not toxic)

Only use the printer in a well-ventilated area, if printing with ABS it is advisable to add a fume hood (with active car-

bon ltering for ductless extraction). Fume extraction is mandatory for use in ofces, classrooms and alike.

Never burn printer lament, toxic gasses and vapors will be generated if exposed to re.

Health:

!

- 3 -- 2 -

������������������ ��������������������

Betyg

Mer om denna bruksanvisning

Vi förstår att det är trevligt att ha en pappersbruksanvisning för din Velleman K8200 3D-skrivare. Du kan alltid ladda ner bruksanvisningen från vår hemsida och skriva ut den själv. Om du vill ha en originalbruksanvisning rekommenderar vi att du kontaktar Velleman. De kanske kan tillhandahålla en originalbruksanvisning. Letar du efter bruksanvisningen för din Velleman K8200 3D-skrivare på ett annat språk? Välj ditt föredragna språk på vår hemsida och sök efter modellnumret för att se om vi har det tillgängligt.

Specifikationer

Alla bruksanvisningar för Velleman 3D-skrivare
Fler bruksanvisningar för 3D-skrivare

Vanliga frågor om Velleman K8200 3D-skrivare

Vårt supportteam söker efter användbar produktinformation och svar på vanliga frågor. Om du hittar en felaktighet bland våra vanliga frågor uppskattar vi om du meddelar oss detta via vårt kontaktformulär.

Relaterade produkter

Bruksanvisning

Dimension SST 1200 3D-skrivare

Bruksanvisning

Clas Ohlson Finder 2.0 3D-skrivare

Bruksanvisning

Afinia H400 3D-skrivare

Bruksanvisning

Afinia H800+ 3D-skrivare

Bruksanvisning

Afinia H800 3D-skrivare

Bruksanvisning

BFB RapMan 3.2 3D-skrivare

Bruksanvisning

BFB 3D Touch 3D-skrivare

Bruksanvisning

MakerBot Replicator 3D-skrivare

Relaterade kategorier